Posting a message to the forum will remove the above advertisement

This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
While you're here, would you mind checking out our Electrician's Insurance section to see if we could save you a few quid? - Specifically our Van Insurance Deals and Public Liability Insurance Deals. Thanks for supporting the forum!

5% Discount from Electrical2Go.co.uk for ALL members! - Click Here

Cookies Electrician's Insurance

support

Recent Content Tagged With support

Thread
EICR for support request and advice

Good evening forumist. Apology in advance, the post is a bit lengthy and please don't cane me too much, am in learning process. I did an EICR for...

Thread by: Gakure, May 30, 2018, 29 replies, in forum: Electrical Forum
Thread
Texecom Tech support charges

I think Texecom alarm systems are hard to beat. When installing an elite 24 some weeks ago, I had a small technical query. After some 26 minutes...

Thread by: stevethesparks, Apr 10, 2018, 3 replies, in forum: Electrical Forum
Thread
Amtech

Has anyone got Amtech fastest and have you had any problems installing it ,also how did you get on with their tech. support line.

Thread by: anthonybragg, Mar 2, 2017, 1 replies, in forum: Electrical Forum
Thread
Best testing software

Hello I was wondering if anyone could help me out with recommending the best testing software to buy. I have been using the NICEIC's online...

Thread by: Andy3438, Feb 6, 2017, 14 replies, in forum: Periodic Inspection Reporting & Certification
Thread
Using a cavity wall gap for cables

Looking at a job that needs cables running up to a loft space. Had originally planned a cable route from CCU through wall into garage (part of...

Thread by: Pat H, Jan 3, 2017, 28 replies, in forum: Electrical Forum
Thread
Domestic Elecsa Technical Support

I'm registered with Elecsa, and quite often use their Technical Support facility. Recently I emailed Elecsa with a couple of questions for their...

Thread by: Midwest, Nov 10, 2016, 19 replies, in forum: Electrical Forum
Thread
PIRform

Did a re install of operating system over weekend and have just tried to access pirform website using both firefox and ie and get stopped with...

Thread by: mhar, May 27, 2014, 5 replies, in forum: Electrical Forum
Thread
Save our trade!

Sick of 5WWs? Sick of scam schemes? Sick of laughable training providers? We as fully qualified electricians deserve better. The public deserve...

Thread by: D Skelton, Feb 6, 2014, 115 replies, in forum: Electrical Forum
Thread
Amtech 2013 software, poor update !

I've loaded the new 2013 Amtech software this week and have found that it's quite poor on the new software they have added an extra program to...

Thread by: WELSHTESTER, Jan 10, 2013, 12 replies, in forum: Periodic Inspection Reporting & Certification
Thread
PIRform

Just giving credit where its due. I've been using PIRform for over a year now and can fully recommend it to others, not only beause of the...

Thread by: yellowvanman, Oct 7, 2012, 4 replies, in forum: Electrical Forum
Thread
SWA or conduit on cage room

Need to run either SWA or steel conduit in an industrial environment by the room is going to be made from a mesh cage. 8 sockets and 4 wall...

Thread by: highspark, Aug 2, 2012, 23 replies, in forum: Electrical Forum
Thread
Conduit Support

Looking for some advice if anyone can help. I've been asked to install sockets in a new build business unit. The company deals with software...

Thread by: Duncan Bennett, Jul 11, 2012, 21 replies, in forum: Electrical Wiring, Theories and Regulations
Thread
Lutron Grafik Eye and LEDs

Afternoon. i have an LED replacement project where I will be using Lutron control. I cant remember the rule of thumb to apply to LED loads e.g...

Thread by: jjnr78, Jul 9, 2012, 1 replies, in forum: Electrical Forum
Thread
BE very carefull PIRform update

Just a word of warning to any of you that use PIRforrm. They have an update online to change it in to a EICR but the update didn't work and then...

Thread by: buttonmoon, Jun 19, 2012, 10 replies, in forum: Periodic Inspection Reporting & Certification
Thread
SolarEdge monitoring portal update

Has anyone else noticed the SolarEdge monitoring portal has been updated today? There's a new admin section which allows quite a lot of...

Thread by: methley, Apr 23, 2012, 90 replies, in forum: Solar PV Forum
Thread
3 phase overhead power supply

Hi folks I need some guidence on this. There's a 3phase overhead power supply feeding exterior accommadation at a hotel. What it seems they've...

Thread by: donnysparks, Sep 2, 2011, 22 replies, in forum: Electrical Forum
Thread
Industrial Roof Fixing strategy

We have not had any commercial projects yet but I have been asked by a family member about the fixing strategy to a modern commercial roof because...

Thread by: confounded, Mar 17, 2011, 8 replies, in forum: Solar PV Forum
Thread
software

seems cheap enough. going to download the trial and give it a go cert software

Thread by: Phil, Jan 1, 2011, 9 replies, in forum: Electrical Wiring, Theories and Regulations
Thread
Megger powersuite problem?

hi does anyone know how to adjust the margins for printing certificates in this program onto a4 landscape paper. basically when im printing say...

Thread by: A-Non-eMouse, Apr 25, 2010, 9 replies, in forum: Electrical Tools and Products
Thread
Supply to an outbuilding

A customer has asked me to price a job for them so here is the scenario. Old milking shed with a 10mm 3 core SWA supply that is to be converted...

Thread by: nrbspark, Nov 15, 2009, 1 replies, in forum: Electrical Forum

Showing results 1 to 20 of 20

- DIY-er trying to avoid a bodge job posted by Koomber. Evening chaps. DIY disaster here. Renovating my bathroom. Going to be laying a LOT of tiles (nice wee metro tiles). Thought I'd join and what not so I can thank people for advice and ask......
- This will be a long job !!! posted by Simon Dale. View attachment 98621 View attachment 98622 View attachment 98623
- Bal or tilemaster ??quartz posted by Chris G. sorry I know there are already many different threads on what adhesive to use for quartz tiles but I’m still a bit nervous about what advise to go with . The tiles are from tile mountain who...
- Hot water tank question. posted by giveitago. Hello everyone. I am looking for a bit of basic advice on hot water tanks. I currently have a warm air heater that heats up the water in my tank via a heat exchanger. The tank is now very old and...
- Boiler advice appreciated. posted by eyeofthetiger. Hi everyone. I have a powermax 150 boiler which I have had since I purchased the house. As far as I know, it is was placed when the house was built and is 18 years old. It is very large, noisy and...
- Are any fittings allowed on mains in before the stopcock? posted by Rob. My stopcock is in a difficult to access location behind kickboards, can I put a coupling on the mdpe pipe coming up and into the house and move the stopcock up into the cupboard under the sink?...

Electricians Directory Post a Domestic Job Post a Commercial Job