As per title any ideas, car just cut out dead and will not start unless I pull the 2 wire plug off the high pressure pump solenoid. I also get no reading at all on the dianostic fuel pressure check. I have 72 psi when connecting my fuel pressure gauge to the line.
Hello all, my first post here and I'm looking for some advice.
We recently moved house and the external garage has a couple of security lights on it. One of them works the other didn't. As they were quite old and the screws seized I was having trouble replacing the bulb (and sourcing a bulb) so...
COVID Update: Emergency Work is Okay; Sitework is Okay 2 meters apart, Work in customers homes in general unless emergency is a NOGO.
I'm trying to find the video and or article where PM questions were extended.
Kids who live with parents at two seperate homes can still go to both homes...
1st post and I’m not a heating engineer/electrician so apologies for lack of proper terminology.
It’s a long story but in essence I had a new conventional boiler replace 2 years ago (Worcester Bosch 28i) and had issues with way heating engineer wired up the new rf thermostat.
Decided to fit a...
Good evening all. Despite of being utterly ignorant on the subject, I have an issue which tickled my curiosity and would like some assistance to understand.
I have a printer (although I'm pretty sure it doesn't matter what appliance it is) that, sometimes, doesn't switch on. After numerous...
Hi, I found this petition and thought I should post it here. I googled the forums and couldn't find a similar post.
https://petition.parliament.uk/petitions/122444
I'm not sure how good or bad the situation is in the UK, but I've heard and read enough to be worried. I read in more than one...
Alessandro
Thread
electric
electrical
electrical work
electricity
qualified
unless
working
I read carefully BS7671, 17th ed., 521.9 and guidance note 1, Table F3 and F5, and no where does it say that flexible cords, such as HO7RN-F can not be used for fixed installations. I hear that was not allowed in the 15th edition but long since allowed. Am I missing something?
Ok, cable under floor. 16m run. My calcs say 6mm tne
Is adequate although on the limit. I don't want to run 10mm unless I absolutely have to
Am I correct?
Hello,
I have a Nissa xtrail (petrol) that is refusing to start... It's a long story but ...two things happened more or less at the same time - 1. Timing chain jumped some teeth due to failed tensioner & 2. Crank Pos sensor developed a fault which somehow melted the connector block!.
Timing...
hi guys new to this so sorry if revisiting old stuff.
I need to run a sub main 200M from the service head to a log cabin
Super eco all LED etc, so 40A 9Kw max demand
if i use the cable calculators i get 185mm cable
we all know power networks cover huge distance with 35mm cable on 100A supply...
hi avery1 i notice few new houses got 5a fused connection unit controlling bath room fans,my q how do they do it if you have 3core cable +earth (timer fan) i always used (3polefan isolater l1 l2 N).:dozey:
Hello all, doing rewire at the moment and i have pit underfloor heating on dedicated ring to save cable. No reason why not right? Conductors in parallel and all that. Not using fcu's just using stat as DP isolator. 7 zones/stats. Design current ok with Ref method B. Am I doing the right...
Eddiesparks
Thread
conductors
dedicated
heating
parallel
rfc
right
underfloor
underfloor heating
unless
using
In middle of rewire customer said they were doing some decorating told them to wait to Monday and I would loosen of the accessories so the could cut round them (all polished chrome) went out to watch the football came back and got a call saying they had a problem the lady of the house had got...
Hi All. I was called out today to a tripped RCD in a domestic split board that not would reset unless the main switch was off. All mcbs off, all phase conductors removed in case of stuck mcb but still no rcd reset unless main swith was off. Any ideas, householder was not prepared for more...
Hi everyone,
I'm sure this topic has been risen plenty of times.
I'm a qualified electrician and I am going to replace a consumer unit for a relative. I am not registered with NICEIC or NAPIT so will be getting it tested by the council.
Can anyone explain the procedure for removing the main...
whazza22
Thread
although
breaking
fuse
main
main fuse
remove
unless
Hi, In your opinon is 20amp more than suitable for an 3 bedroom upstairs circuit, cant think why they really need to be 32amp maybe if you started plugging in 3kw heaters :)
thanks
Hi all, job visited they are extending downstairs wc and fitting a shower(quadrant)the meters gas, elec and old wilex rewireable cu. they want a new cu fitting, shower feed, lights etc. I have told them the cu will have to be moved out of room but meters can remain boxed in! (In cupboard with...
Hi Guys,
Hope ye can give me some advice and help here.
Im a self employed sparks in Ireland and iv been out on my own for about 4years now but getting nowhere so i was thinking of moving to London in November but i need all the help i can get from ye as i dont know where to start.
I see ye...
peter_k800
Thread
electrician
electricians london
employed
grade
help
london
moving
self
self employed
sparks
thinking
unless
where
Called to a ring main fault. Customer has had some work done about 3/4 months ago. Have not yet found the fault but noticed on inspection 3 of these ring main extensions. What do you think. 15amp thru crimps!!
067256
Thread
crimps
fault
found
main
rating
ring
ring main
things
unless
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.