I will start by apologising to @westward10 as he will have had to take time out to move this thread to the correct section.
I am terrible at putting my threads in the right section and westward always moves them to the correct location.
This time I did actually look... and look... and look...
Hi guys,
I have used the following image circuit to control the load.
AS you see the SCRs are controlled by AC signal and The opto-triac is always ON. If the load is a resistor, When the AC signal is positive the current passes through the SCR1 and when it's negative it passes through the SCR2...
I have 18 panels in 2 strings (37.8v open circuit voltage each) to be connected to a Fox H1 inverter. The manual says the below. Is the 600v open circuit voltage per string or for both strings combined?
H1 series inverters can be connected with 2-strings of PV modules. Please select suitable PV...
Hi every one. I have a NC relay with the below features which is written on the relay:
Input voltage:12V dc
Output switching voltage: 220V ac
Output switching current: 5 amp
Can I use this relay for a 400V ac, 0.1 amp Output case?
Can the relay stand up to this high voltage?
Thanks
I have a 5th wheel caravan. It has had a transformer fitted for UK electrics. The air con, microwave and fridge freezer have stopped working because they run off the lower voltage US electric box.
I need an electrician who understands the American electrical system.
The caravan is in Kent.
Any...
I wanna control (reduce) the speed on my AC duct fan by inserting a variac between the mains and the duct fan.
The duct fan is currently connected to the mains (230v) in a junction box close to where I wanna install the variac (3 meters).
The variac has 4 connection-pins:
L - mains
N - mains...
I've been fault finding an issue in a domestic property, the situation is as follows...
RCD spur that is protecting outside sockets,
This spur is on the downstairs 32A ring, the sockets directly on the ring pass RCD tripping test.
The cables coming into the spur won't trip when tested...
I ran 208 v power to a rottler em69p cnc machine. it calls for 208/240 v 3 phase. 60amp rottler em69 installation manual
everything is wired using 3 #6 hot and #8 ground
to 6/4 SO cord drop to the machine . inside the machine again the wiring is 3 #6 and #8. I checked voltages and got 208-209v...
I am unable to find voltage drop of normal silicon diode(0.7v) on Voltmeters during Proteus Simulation. Also we consider 0.7v drop of diode equivalent to DC Source of 0.7v but DC voltmeter is not showing any output and AC Voltmeter shows around 5 volts drop across diode instead of 0.7V.Kindly...
I designed basic clipper circuit using single 3.3v Zener.When i simulate this on proteus and while checking output by keeping knob on AC of respective chanel and output shown is 2v positive and 2v negative from refrence ground(obviously wrong).When i change knob to DC it shows correct output of...
Could anyone shed some light on what might be going on here, before I cut a trap in the laminate to find out. I have a dead socket on the end of a 2.5mm cable of unknown origin. L-E L-N N-E all 0 volts. Insulation resistance between the ends all 1000M Ohm. No continuity any conductor back...
I'm building a new property consisting of 4 sperate discrete buildings, all roughly in a straight line. My question: Is there any advantage to connecting the buildings supply in a ring rather than just daisy-chaining them (i.e. radial)?
I was planning to run a single 1 AWG backbone supply up...
Hi there
I can't wrap my head around a problem I have when trying to connect my dual 12v battery system in a camper. When I plugged in my VSR ( Orion from the brand Victron) i measured the + input was 3 volts although engine running (and app saying 14v input...). I thought the wire were too...
Hi Problem: I have 5 (240v) led lights in a bedroom on a single on/off switch (not dimmer) and all the leds worked fine until last w/end. Then with the switch being off, the leds would flicker/strobe. Switch on and they all work fine. Disconnected the switch completely and still the same...
Hi everyone, I have a Vauxhall insignia 2.0 cdti non starter, cranks but no start.
It also doesn’t crank very fast, tried new battery and still the same, it cranks kind of sluggish and the dash lights start to flicker, live voltage readings at crank drop from 12v to 7v, does that mean the...
Hi Gents,
We will convert our shop voltage from 120v to 220v.We will replace the old transformer 75KVA-480v (208/120 V) by new one (400/230 V). The question is can I use the existed panel boards (see the information
below) or not?
see pic links please
https://ibb.co/X3zqFqC...
Wondering if anyone else has had this, getting 24v between live and neutral at pendant when dimmer is off, which means the light isn’t fully going off it’s still sort of glowing. When I replaced this for a regular switch it sorted the issue, just wondering if anyone else has had this and if just...
During an FLI test recently on a high resistance extraneous part (several thousand ohm) I decided to test what voltage appeared on the metal while the test was been carried out.I used a Metrel M1 3000.I measured approx 40 volt. Its well over 20 years since I conducted a similar test and my...
Just had a call from an M&E client of mine and good mate asking to pick my brains.... large 3ph biomass boiler with (I assume variable speed) 1ph fans internally. Says he's got 230v L-N/E on the connecting plug but when the fan gets connected there's nothing on the internal fan connections...
I have two main panels each 150amp breaker. House was built in 83 and lived here for 6 years no issues. About 6 months ago we had a power surge and our main ac fail (hard short) and tripped the breaker. Had the unit replaced but it seems since then we have had issues with lights diming and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.