IR Test ? Weird issue N-E only

[Soulsurfer]

Hey all, just doing some tests on a small extension and have a weird issue with IR on lighting circuit, all switches left open as nightmare to strip all lamps, fittings etc.. L&N to CPC not ramping up over 7-15V DC then resetting test !

L-N on 250V or 500V 31-32 Meg
L-E 32.6 Meg
N-E won't go ! Tried all obvious things to remove out of circuit plus new mains smoke detector etc.. but still no good, any ideas ?
Only fed at moment on a B MCB 6A no RCBO etc.. head scratching or feeding something hidden maybe or a fault ?
Thanks.

 

[Wilko]

TNCS ?

 

[Soulsurfer]

TNCS ?

Yes mate.

 

[buzzlightyear]

Hey all, just doing some tests on a small extension

new or old ?

 

[Soulsurfer]

new or old ?

New extension but only extended ring from upstairs and , lights from upstairs.
All ring testing perfectly.

 

[westward10]

Why have you left all the switches open.

 

[Leesparkykent]

Yes mate.

Main switch off?

 

[Soulsurfer]

Why have you left all the switches open.

Just to avoid stripping out awkward light fittings and dimmers initially to save time before doing full tests. Also thought L&N-E would go through fine but nope

 

[Soulsurfer]

Main switch off?

Left all mains on to rest of house as they wouldn't have juice off while in there !
Just pulled related L,N,E from terminals at Cu to test

 

[buzzlightyear]

connected right!

 

[Leesparkykent]

Parallel path on that circuit you are testing. Switch the lot off an try it again.

 

[Soulsurfer]

connected right!

? The lights ?

 

[westward10]

Just to avoid stripping out awkward light fittings and dimmers initially to save time before doing full tests. Also thought L&N-E would go through fine but nope

I still don't understand why you have left them open.

 

[Octopus]

Fault finding your own install work is always the easiest......

 

[Soulsurfer]

Parallel path on that circuit you are testing. Switch the lot off an try it again.

Thanks Lee, I'll try next time when customers not being a pita !

 

[westward10]

Left all mains on to rest of house as they wouldn't have juice off while in there !
Just pulled related L,N,E from terminals at Cu to test

You should have the cpc connected to the earth bar.

 

[Soulsurfer]

I still don't understand why you have left them open.

I figured in my early testing career that it would save frying any LED downlights or dimmer module etc.. as would take a good while to disconnect all fittings / lamps etc.. straight away. Tested at 100 & 250 V too to save any issues but none would ramp up test voltage to CPC

 

[Soulsurfer]

I still don't understand why you have left them open.

I figured in my early testing career that it would save frying any LED downlights or dimmer module etc.. as would take a good while to disconnect all fittings / lamps etc.. straight away. Tested at 100 & 250 V too to save any issues but none would ramp up test voltage to CPC

You should have the cpc connected to the earth bar.

Always done IR with every conductor out and in croc clips ? NIC assessor said was right way ? Thought would cause parallels if left in Earth bar ! Maybe I've made a fundamental boo boo

 

[westward10]

Won't fry anything and I only ever resort to 250v if I get odd readings to cancel out possible filtered equipment.

 

[Octopus]

RE awkward fittings and dimmers ..... Just fit standard switches and omit light fittings and do continuity and ir tests first ...... Can save hours of hassle