Discuss MOELLER DILEM10 240V 5kva in the Electrical Forum area at ElectriciansForums.net

Welcome to ElectriciansForums.net - The American Electrical Advice Forum
Head straight to the main forums to chat by click here:   American Electrical Advice Forum

C

craig sagar

Hi hope someone can help...

my MOELLER on my hydroraphic dipping tank went faulty so i took it out and bought a new one,i took photos of the wiring diagram.
However my daughter who's camera i took the photos on erased the sd card to take holiday photos with now im a little stuck as to what goes where...
The MOELLER has a thermostat wh7016c thermometer running to it and that then turns on my heater to warm the water up in my tank..
Could someone do a quick diagram as to what goes where please..

View attachment 35602

View attachment 35603

View attachment 35604
 
The circuit from the stat will switch the coil which is connections A1 and A2. So you should need a neutral to A2 and the switched side from the stat to A1, assuming it to be 230v. The heater should go through terminals 1 to 6, so terminals 1, 3 and 5 will switch to terminals 2, 4 and 6. It is not clear if the NO terminals are utilised.
 
thanks for the help i kinda get it so correct me in im wrong please

so the the load out of the thermometer goes to a1 and a neutral to a2 which can be taken from any neutral in the control panel
now the heater wires ive got 2 heater elements the brown wires go to the MOELLER and the neutrals of the 2 heaters go to the neutral again from anywhere in the control panel

so the thermometer is what gives the MOELLER its supply or do i need to also put a supply power to the MOELLER
 
Last edited by a moderator:
That doesn't tally with your contactor, the drawing shows two NO (normally open) and two NC (normally closed) contacts. Yours has three NO contacts.
 
Who sent you that, it shows the contactor used to switch between two loads when the stat calls, unless we know the full details of the control and what it is supposed to do then we can only guess.
 
ive took it off the tank ill add photos
but basically i have an on/off switch for the actual power box of that a live and neautral go to 2 switches that turn my pump on to circulate the water and to open the magnetic switch.
then i have the thermometer that went to the moeller and then from that 2 heater cables. ill try and get a decent photo to post up,
I might even get someone to draw what goes where haha,but so far thanks load for the help
 
ok ive took all the wires off but know where they went as there only to switch to open a magnetic switch and then another to turn on my water pump which circulates cotaminated top coat water that ive sprayed xylene based activator onto.

View attachment 35606
 
in the photo the moeller is upside down which ive only just noticed.
the three switches only 2 are in use i know the connections to those its the thermo to the moeller,had my daughter not deleted the memory card it would be easy to do haha..
i didnt think it would be so difficult to connect a thermometer to the moeller to get it to turn the moeller on and off..
there was i remeber a wire coming going into a2 then a bridge wire coming out and going to the connnection next to it looks which looks like 14 in the picture
 
Where the 2 red wires are on the moeller is that where the thermometer load connects to ? or is that where the power of the control panel on switch goes.
Then the blue wire out of the thermometer where does that go as im sure that was in the moeller connected to pin L2
Then do the heater elements wire to the moeller or do they go to a switch.
the way the board was wired up originally it was that only the bridged wire was connected then the thermo wire was in the opposite,so a1 a2 then there was a wire next to a1 and then another wire at L2
Oh i forgot to mention that i have added another heater,when i first got the tank it only had a small heater in it, that took hours to heat the tank to temperature.
Id be made up if someone could draw a diagram to make the moeller function correctly.The pump and electronic switch is simple to connect up.
Thanks to anyone that can do this for me as not having my tank working properley is a nightmare, ive got the heaters plugged in to a double socket at the moment,which im sure isnt good when the cable is getting hot eeeeeeeek...
Its nice to feel sake especially around water mixed with electricity :)
thanks again for any help

any wire you see on the control panel is disconnected i should have took a photo showing this....
 

Reply to MOELLER DILEM10 240V 5kva in the Electrical Forum area at ElectriciansForums.net

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Electrical Forum

Welcome to the Electrical Forum at ElectriciansForums.net. The friendliest electrical forum online. General electrical questions and answers can be found in the electrical forum.
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock