Some advice regarding 125mm hole for cooker hood fan please?

[valleybilly]

+ 2mm addition to core drill sizes is more than enough for fitting flexi ducting . The bigger ducting size also reduces dB when in full power mode so 150mm is even better on a 100mm system.

 

[LankyWill]

127mm is the standard for cookerhood extracts, if your struggling to fit the duct through get a hammer and block of wood and wack it.

 

[Pete999]

127mm is the standard for cookerhood extracts, if your struggling to fit the duct through get a hammer and block of wood and wack it.

Like the technical talk there Will, "get a hammer and a block of wood and wack it out" nice bit of engineering speak like it.

 

[egg67]

A lot of MI will say core size 5mm bigger than ducting it allows for movement and gives you a bit of leeway to set the duct so condensation does not flow back to fan.
Handyspacks as pete999 said saves a lot of making good

 

[Midwest]

It won't strain the motor (might even reduce the load slightly, depending on the characteristics of the motor) but it will reduce the flow for a given fan speed (as will more duct length or bends). Whether this matters to you or your customer is hard to judge.

A mate of mine, had to route his ducting through 2 x 45' bends and 3.5m of ducting. Still stops his kitchen steaming up.

 

[HandySparks]

To stop break of the material you are drilling through

Handyspacks as pete999 said saves a lot of making good

I've never had any break away of material on the exit side when using a core drill.

I guess if you have the drill on 'hammer' you would, but that's not how most core drills are used.

Surely, getting a core drilled hole to meet up accurately when drilled from both ends would be difficult?

 

[Pete999]

I've never had any break away of material on the exit side when using a core drill.

I guess if you have the drill on 'hammer' you would, but that's not how most core drills are used.

Surely, getting a core drilled hole to meet up accurately when drilled from both ends would be difficult?

Not really drill through from one side until the pilot shows and then drill through from the other side with the core drill engaged, rocket science is not required.

 

[HandySparks]

Not really drill through from one side until the pilot shows and then drill through from the other side with the core drill engaged, rocket science is not required.

But why would you bother? I've never had any problems with drilling from one side only with a core drill.

 

[Midwest]

I've done both ways, ones okay for flexible ducting not for solid. Let the machine do the work, and don't be so impatient

 

[Pete999]

But why would you bother? I've never had any problems with drilling from one side only with a core drill.

Do what's best for you Mate I'm only explaining the right way of doing it, if your way suits you carry on.

 

[Pete999]

Not really drill through from one side until the pilot shows and then drill through from the other side with the core drill engaged, rocket science is not required.

 

[egg67]

Think it's just the way you are shown How to do things , was always told to drill a pilot hole first then the biggy and go at it from both sides, but that was 34 years ago so things change with time, drill bits have got better and making good is just a bit of silicon

 

[Pete999]

Not really drill through from one side until the pilot shows and then drill through from the other side with the core drill engaged, rocket science is not required.

Think it's just the way you are shown How to do things , was always told to drill a pilot hole first then the biggy and go at it from both sides, but that was 34 years ago so things change with time, drill bits have got better and making good is just a bit of silicon

 

[Pete999]

Now you have to agree that's bull shyeet, not the vid your statement it's only a bit of silicone.

 

[egg67]

Think it's just the way you are shown How to do things , was always told to drill a pilot hole first then the biggy and go at it from both sides, but that was 34 years ago so things change with time, drill bits have got better and making good is just a bit of silicon

 

[jackhammerJIM]

If you do plan on drilling from either side make sure the pilot bit is the exact same size as the sds bit .

 

[marc8]

I've just measured some rigid 100mm ducting I have Murdoch, the outer diameter is 103-104mm. I'm pretty sure with ducting (unlike conduit) the specified size is for the inner hole, stand to be corrected though? Flexible ducting, although more malleable has an even bigger outer diameter relative to its inner diameter.

I also remember drilling a 107mm hole for 100mm rigid ducting and it 'just' scrapes through.

220 x 90 mm is approx 6"
204 x 60mm is approx 5"

 

[marc8]

Think it's just the way you are shown How to do things , was always told to drill a pilot hole first then the biggy and go at it from both sides, but that was 34 years ago so things change with time, drill bits have got better and making good is just a bit of silicon

lucky these days from what i have seen drill pilot hole, drill in 1" then club hammer, think it is in case they loose to many diamonds or is it too much time i am not sure maybe my age.

 

[egg67]

Silicon, sillycon or silicone it's all the same at the end of the day, just when I started out was drummed in to me that you do a good job as in Measure twice cut once, drill little them bigger, keep mess to a minimum and leave a good job

 

[NDG Elecs]

I think you are overthinking this a bit HHD. Core your ~105mm hole and use a 125-100mm reducer above the fan. It will work fine.

A good tip for hard engineering brick is to core through by around 25mm then stitch drill holes around the circle to speed up the remaining coring.

I sometimes core from both sides, depending on the finished surfaces inside and out. Does make it much harder to use rigid ducting though doing it that way. I tend to core from the outside to the inside, this due to the dust levels.