Stripping Alarm Cable (cable core keeps breaking)

[numberwrong]

"Stripping Alarm Cable (cable core keeps breaking)"

I'm using the 6 core cable that came with the Honeywell alarm system I got

Tried with Automatic style wire strippers, stanley knife, side cutters etc. but the steel core is very prone to breaking.

What tools or techniques would people recommend using?? Other cable this thin like Cat5 is just punched down in to the socket or crimped

 

[Guest111]

Strip the outer using the rip cord provided and then trim off the plastic sheath,as for the inner cores I just use side cutters with no problem,but then again I have been doing it for over 30 years.

 

[numberwrong]

Yeah, the outer isn't a problem because of the rip cord. My side cutters aint as sharp as they could be... Haven't tried the good old-fashioned flat black crimp and strip tool, maybe this is the solution?

 

[Guest111]

Yeah, the outer isn't a problem because of the rip cord. My side cutters aint as sharp as they could be... Haven't tried the good old-fashioned flat black crimp and strip tool, maybe this is the solution?

no mate don't think one of them will do it,best just buy some new cutters or a decent cable stripper,have you many to do?

 

[numberwrong]

was thinking something like this? no good?


Yeah, I've got loads to do (Alarm system for my 3 floor house) so willing to spend dollar on something that's quick and good

 

[Guest111]

You could try it but it depends if the strippers go small enough there is a company called ideal industries based in warrington that do a nice little tool for smaller sized cables costs about £14

 

[KAS1]

That's not even good enoigh to stir paint with, sling it in the bin.

was thinking something like this? no good?
View attachment 16671

Yeah, I've got loads to do (Alarm system for my 3 floor house) so willing to spend dollar on something that's quick and good

 

[Guest111]

That's not even good enoigh to stir paint with, sling it in the bin.

well at least help the man,don't just state the obvious,we may know that but maybe he doesnt.

 

[numberwrong]

That's not even good enoigh to stir paint with, sling it in the bin.

I'm sure Knipex would say otherwise!!

I've found my solution:

This type of wire stripper works perfectly (forgot I owned a pair!) They're sharp enough to cut the insulation without putting too much strain on the steel core whilst stripping.

Thanks for all responses.

 

[Fast&Rough]

Use your teeth

 

[telectrix]

steel core???? surely it's copper. i just use side cutters.

 

[Des 56]

Use your teeth

That is one excellent method although I always use my finger nails

 

[tazz]

This might sound daft but most delta 6 core have 2 black cores one is copper stranded the other is a plastic blank. I dont know why this in there.?? But if your trying to strip this blank core youll be there forever..

 

[KevinS]

Use a Stanley knife, jam the cable between the blade and your thumb and pull

 

[telectrix]

spread the cores so they're in line, side cutters, strip all 6 cores in 1 go. easy.

 

[Deleted member 26818]

I use the scissors on a Swiss Army knife.

 

[KAS1]

C'mon lads don't be so hard on him he's only asking for some guidance, give the poor lad a break.

 

[KevinS]

C'mon lads don't be so hard on him he's only asking for some guidance, give the poor lad a break.

Who is being hard on him, sounds like good advice everyone

 

[Deleted member 26818]

C'mon lads don't be so hard on him he's only asking for some guidance, give the poor lad a break.

Stop trying to stir things up Kas.

 

[onions1066]

C'mon lads don't be so hard on him he's only asking for some guidance, give the poor lad a break.

Kas you try and stir up every thread, it gets boring after a bit to be honest.