18th edition consumer unit

[longers30]

Hey all,

I have just finished a rewire of a 1 bed house and just have the board left to install. I am a qualified sparky but now work as a project manger so haven’t carried out much domestic work in the last couple of years. I know that the requirements for installing consumer units has now changed and am wondering what are the requirements with regard to cable entries into the board. I have the cables all dropping down from the ceiling where the existing board and meter position is in the entrance hall. Any advice would be appreciated.

 

[Dave OCD]

My preferred method is to bring all cables through the large rear knockout, suitably grommeted of course. And I generally space the board off a little with a couple of pieces of small batten the same height as the board to facilitate this. If you use the top knockouts you then need several glands to achieve the required IP rating and it doesn't look as good either.

 

[buzzlightyear]

ip rated on top open grommets sealed with fire seal ,if you cannot get the cables behind
Everbuild Fire Mate Intumescent Sealant white 33
(EVBFIRE)

 

[Charlie_]

1 bed house, how many circuits?
Maybe 5?
I prefer the rear entry method (no pun intended)
Failing that, I would use trunking

 

[buzzlightyear]

I prefer the rear entry method

yes matron ,LOL.

 

[Octopus]

Rcbo board ....

 

[Charlie_]

What’s the earthing arrangement?

 

[DPG]

Rcbo board ....

Didn't know you were a fan of RCBOs Murdoch.

 

[Dustydazzler]

Rcbo board , little bit MT4

Bingo bango bongo

 

[GBDamo]

What’s the earthing arrangement?

Go on, i dying to know how the earthing arrangements dictate cable entry method in to a CU.

Are you giving Pete an afternoon off?

 

[Charlie_]

My question on earthing;
TT - upfront RCD or going for the option of having the tails enter the board with one of those special stuffers that apparently guarantee the board from becoming live.

Day off;.. we’ve all had one of those today in the iom, it’s a national holiday

 

[Deleted member 26818]

Top horizontal surface of the board has to be IP4X or IPXXD, the front sides and bottom surfaces have to be IP2X or IPXXB.

 

[longers30]

Thanks for all the replies guys! It’s a T-N-CS earthing arrangement. As the board is going to be tight to the ceiling there won’t be room for trunking so may do the rear entry method. This is a photo of the old board being replaced.

 

[Octopus]

Thanks for all the replies guys! It’s a T-N-CS earthing arrangement. As the board is going to be tight to the ceiling there won’t be room for trunking so may do the rear entry method. This is a photo of the old board being replaced.

I don’t believe that head was that close to the ceiling when it was installed ...

 

[littlespark]

Not strictly needed, but I would bring the board down the wall a bit to a more user friendly height. With trunking to hide cables.

 

[littlespark]

Love the smart meter just hanging there. 5 star installation

 

[telectrix]

Not strictly needed, but I would bring the board down the wall a bit to a more user friendly height. With trunking to hide cables.

or chase them in. then CU on a bespoke piece of board, spaced off wall with 4 bits of 1/2" long 20mm pvc conduit . then rear entry.

 

[littlespark]

Everyone seems obsessed with rear entry on this forum. Nudge nudge, wink wink. say no more, guv’nor

 

[richy3333]

Why do we fit RCDs for stuff buried in a wall less than 50mm deep if not to guard against things that aren't "normal use"??

or chase them in. then CU on a bespoke piece of board, spaced off wall with 4 bits of 1/2" long 20mm pvc conduit . then rear entry.

Or use a stand off bracket rather than battening. Many manufacturers sell them.

 

[Midwest]

As the board is going to be tight to the ceiling there won’t be room for trunking so may do the rear entry method. This is a photo of the old board being replaced.

Think of the little people.

 

[Midwest]

And I generally space the board off a little with a couple of pieces of small batten the same height as the board to facilitate this.

I do rather hate mixing pieces of organic matter with metal. Just doesn't seem very karma to me. What about plastic, or even some manufactures spacers.

 

[Dave OCD]

Nah I like my little battens.

 

[DPG]

I like batten berg.

 

[magnoliafan89]

I bloody hate people who do rewires and still put the new board back at ceiling height....especially when its in the smallest cupboard they can find....even more infuriating to finallt get the cover off to find a birds nest

 

[Zac lynch]

Hey all,

I have just finished a rewire of a 1 bed house and just have the board left to install. I am a qualified sparky but now work as a project manger so haven’t carried out much domestic work in the last couple of years. I know that the requirements for installing consumer units has now changed and am wondering what are the requirements with regard to cable entries into the board. I have the cables all dropping down from the ceiling where the existing board and meter position is in the entrance hall. Any advice would be appreciated.

I think you must do short course called part p etc ???

 

[longers30]

Thanks for all the replies. Looks like back entry will be the best way to go.
On a side note I’ve seen online that suppliers are selling the semi blind grommets which it says are ip66 rated for use on cu’s. Would these comply with the new regs as I haven’t seen this method shown anywhere?

Cheers

 

[longers30]

I assume the new board can be fitted to the existing wooden board behind also?

 

[Pete999]

I assume the new board can be fitted to the existing wooden board behind also?

I assume the new board can be fitted to the existing wooden board behind also?

Why wouldn't it ?

 

[longers30]

Not sure thought I read something about it but I must be thinking of something else
Last point the existing tails are 16mm which will be fine as there will be little load being used. Anyone know how much roughly the DNO charge for coming out to pull the main fuse and back to reinstate supply after? It’s wpd here.

 

[Pete999]

Not sure thought I read something about it but I must be thinking of something else
Last point the existing tails are 16mm which will be fine as there will be little load being used. Anyone know how much roughly the DNO charge for coming out to pull the main fuse and back to reinstate supply after? It’s wpd here.

Have you consulted the seal fairy??