Am I being stupid

[Redvanman]

Ok I know you guys are shy at coming forward but tell me what you think,

I have some LED floor lights to be put into a tiled bathroom floor.
The cut out size is 20mm and the flex on the light is 1M therefore I was thinking of crimping the flex to T&E under the floor and heat shrinking it so that the cables will run to a JB outside the bathroom.

Any better ideas would be appreciated

 

[telectrix]

if you have room under the floor you could use MF line enclosures with wagos inside.

 

[shanky887614]

Ok I know you guys are shy at coming forward but tell me what you think,

I have some LED floor lights to be put into a tiled bathroom floor.
The cut out size is 20mm and the flex on the light is 1M therefore I was thinking of crimping the flex to T&E under the floor and heat shrinking it so that the cables will run to a JB outside the bathroom.

Any better ideas would be appreciated

I would recommend soldered over crimped, the problem with crimped is they can generate quite a bit of heat.

had one a while ago that had the insulation tape burning

 

[trev]

Yes you are.

Seriously though, If the lights are lifted is there going to be enough slack on the cables to get to any joint? My guess is that there would be but I'd be more likely to go with wagos in a box mate.

 

[trev]

Scouse beat me to it, yet again

 

[Redvanman]

The problem I have is the 20mm cut out which stop any type if enclosure being used but I would still want to be able to pull them out afterwards in case of any failures plus the original install would have to be done after the tiles are laid.

 

[shanky887614]

The problem I have is the 20mm cut out which stop any type if enclosure being used but I would still want to be able to pull them out afterwards in case of any failures plus the original install would have to be done after the tiles are laid.

2 lever wago's?

I would extend the cables personally though.


why not bring the cable to the skirtingboard?

you can have your connections there then (couple bits of 20mm conduit/copex) underfloor to make it easier)

 

[trev]

Well maybe crimps and heatshrink are your only options.

 

[shanky887614]

have a chat to the tiler and drill them first or you will be sorry if you crack one

 

[davesparks]

I'd go with the solder and heatshrink option I think.

 

[Redvanman]

Believe me I'm not drilling the tiles I'm leaving a 2" hole in the floor so that he can drill the tiles and stick em down
Any way thanks for all your responses glad to see I wasn't making a complete --- of myself for a change
i would have done the thanks thing but it's not working but will give it one more go

 

[trev]

glad to see I wasn't making a complete --- of myself for a change

What makes you think you haven't?

 

[Redvanman]

What makes you think you haven't?

And to think I just thanked you

 

[Octopus]

Does the LED driver instructions state a maximum length of cable?

Lights in a bathroom floor - what ever next!

 

[Redvanman]

No driver 240v sealed unit

And I no floor lights stupid really probably as stupid as plinth lights but hey they pay I install

 

[trev]

And to think I just thanked you

Bull, red rag mate sorry, too good an opportunity to pass up

 

[Octopus]

No driver 240v sealed unit

And I no floor lights stupid really probably as stupid as plinth lights but hey they pay I install

I've installed some in our new kitchen - they look really cool!

Trev - I can edit mine!

 

[Redvanman]

I've installed some in our new kitchen - they look really cool!

I had a feeling after I posted that comment someone would shoot me down.

Ive no doubt that your kitchen looks

 

[Octopus]

Ive no doubt that your kitchen looks[/B]

..........

 

[Redvanman]

..........

Cool!!