PVC Conduit Question

[RDB85]

I’m looking to buy some PVC Conduit for some security lights rather than clip the cable. We don’t use it in work. But I know I need 20mm conduit but would I be okay using 20mm inspection elbows? I assume they just fit inside?

 

[Dustydazzler]

Never used a bending spring. I will order one and do all my straight cuts and see if I have any scrap left to practice with.

don’t forget to give the conduit a good hard rub before you try to bend it...

 

[telectrix]

what's wrong with inspection elbows? how else do you come through a wall and then 90 degrees (up/down/left/right)? do youm bent the tube and have it sticking 4" off the wall?

 

[westward10]

Back entry terminal box, manufactured bends look terrible.

 

[Pete999]

what's wrong with inspection elbows? how else do you come through a wall and then 90 degrees (up/down/left/right)? do youm bent the tube and have it sticking 4" off the wall?

Me, I use a back entry on an end box and shoot off from there, better than an Inspection elbow I reckon, but each to their own I guess.

 

[littlespark]

Careful with the springs. Get one from the same supplier as the pipe you are using. There can be discrepancies between the inside diameter of different manufacturers. so it it can either be too tight to push in, or too loose and cause wrinkles.

whoever said bending the pipe with a spring would be more economical.... it depends how good you are at bending.

I see nothing wrong with using manufactured bends for neatness. All uniform radii, all the same.

 

[Risteard]

I would avoid manufactured bends and elbows they look terrible in any instance.

Not to put too fine a point on it, but they are truly awful.

 

[RDB85]

I’ve ordered the pvc adhesive. The diameter is 20mm but the elbow and inspection bends and even the end boxes don’t fit inside the conduit. As I wanted to get it all measures and test fitted before using adhesive.

As the tubing doesn’t fit over them I assume you would make some cuts in the end to make the diameter smaller?

 

[ferg]

The tube fits inside the accessories???

 

[freddo]

???? The pipe goes INSIDE the port on the fittings, it should stay there on its own, no need to cut anything, it just pushes in.

 

[RDB85]

???? The pipe goes INSIDE the port on the fittings, it should stay there on its own, no need to cut anything, it just pushes in.

I know it should do this doesn’t it’s the same diameter. So it doesn’t push inside. Not sure if it’s the conduit or the fixings I’ve bought. The fixing are a brand make and the conduit was given to me.

I will get a photo to show you what I mean. I assumed that the fixings should fit inside, so I was a bit confused when they didn’t and thought do I need 25mm tubing.

 

[freddo]

Can you post a photo showing the issue? It's not something I've come across before!

 

[Risteard]

I know it should do this doesn’t it’s the same diameter. So it doesn’t push inside. Not sure if it’s the conduit or the fixings I’ve bought. The fixing are a brand make and the conduit was given to me.

I'm going to guess that you have 25mm conduit with 20mm accessories/fittings.

 

[RDB85]

Measures the conduit and the inspection bend both 2cm.

 

[littlespark]

Plumbing drain pipe comes in a 21mm diameter size. Could be you’ve been given drain pipe.

 

[freddo]

21.5mm overflow pipe?

Oops, crossed with LS.

 

[ipf]

Who 'gave' you the conduit/pipe?

 

[RDB85]

So looks like I need some 20mm pipe then. Thanks it was a mate, he’s not a plumber though it was a fellow spark lol

 

[Pete999]

No not if the conduit is 20mm, 20 mm everything Saddles, fittings and bending spring.

 

[telectrix]

Measures the conduit and the inspection bend both 2cm.

that'snot conduit. it's a wet-pants' water pipe.

 

[Mike Johnson]

Yes overflow pipe, but if you must use it, asa it is thick walled I have successfully turned it down at the end by putting a mandrel inside and turning it on an electric drill with some sandpaper or file, gets you out of a problem if needs be.