Hi Everyone
May be someone could shed some insight on the sizing and provide some suggestions:
3 phase Generators (400 V, 50 Hz) have the ability to sustain 250% kVA of its rated kVA at 30% voltage dip.
Suppose a machine needs to be powered by a standby generator during a power outage. It...
Got a customer with a 3 phase looped cut out. Only use one of the phases and there is likely a second fuse on the adjacent holder/phase.
I have asked the DNO to take a look and advise as the customer wants an EV charger. With a looped supply you should get dnos advise first. ENA guidance also...
Hi All
New member on this forum 1st post
i need some good sound advice please I am a maintenance electrician and I have been asked to quote for a 3 phase and neutral electrical supply at 125amps per phase for a chiller unit that is to be hired ,to be totally honest I am out of my depth . My...
Hi
I am new to electrical engineering. I want to measure the 3 phase voltage near the water pumpset motors.
I have connected phase lines to earth through a diode and six 1 mega ohm resistors (measuring the voltage across resistor). The same earthing wire is connected to ground in my dc circuit...
Hello everyone
I have just bought a new lathe, (used) its on its way to me from other end of the country now.
I have only just realised i may have an issue.
The machine is 3 phase and i was intending to go down the VFD route but because its a dual speed motor im not sure i can.
See attached...
Hi All,
I am just about ready in my new workshop to buy and start using the 3 phase equipment i will need for my business. The biggest of which will be the press brake rated at 12.5kw max.
There will be a few other units but smaller - around the 1 to 3kw rating range, so with that i am looking...
Hi, in my garage I have a 3 phase RCCB that has tripped and I just can't get it to reset, even with all the downstream MCBs switched off. Bit of a nuisance really as mother in law has no power to her flat above the garage and the garage door and front gate don't work.
I tried uploading photo...
Hi - first post, so I hope I get the tone right. I do pay professionals to do the work, but have a technical background and like to understand what's being proposed and why.
My house has a 3 phase supply. Everything in the house runs off a single phase. We've just had a 7kW car charging point...
Hi all,
Background- I rent commercial premises for a small cabinetmaking business. Lots of 3 phase machines and 240v circuits. The site is on a farm where the main supply enters the landlords unit to a distribution board where it is then split to various rented units. That board looks like...
Hi guys/gals
I have been asked to install some 230v sockets and lights in an old refrigerated trailer, that would be used as a store on a quarry site.
The trailer has a 3 phase generator built on to the side to originaly work the refrigeration unit, but as everything involved with the...
I work in a location that was once a Machine shop showroom. We have 208/230/480 etc in the building. I need to install a temperature chamber that requires single phase only 208V or 230V supply. I have a 100 amp rated disconnect literally in the exact location this needs to go. I've read for...
I have to supply a 3 phase + neutral circuit but I have to run it through a contactor. The contactor is 3 phase no neutral and will be bushed onto the left side of the board with 2 bushes (one for feed, one for load).
The other side of the board is bushed onto some trunking where the load will...
3 phase standby generator of rating 30KVA is to be install in the lightning prone area. The utility main line is TT arrangement where neutral point is grounded with 3 phase and neutral wire provided to load system.
A separately driven generator ( standby generator) is also needd with TT...
I don't normally get involved with domestic work but this job is for a family member so I cant Simpley say no.
the house is a large property with a 3 phase 100A supply.
I think the earthing is TT but not 100% sure of that yet.
customer has bought a 12.5Kva generator to use as a backup supply...
Hi, I hoping someone can assist me. I’ve taken delivery of a control box from Japan, which is powered by 3 phase at 200v. The wires are red, black, white and green. Any ideas how or if I can wire this to make work in the UK via standard 240v or 110v please?
I have a 10 HP -230 volt 3 phase hydraulic press brake. I just installed a new 40 HP rotary converter panel with used WEG motor. The problem i am having is the volts going into the press during a load is dropping from 245 to 195-200 volt. Which means i'm loosing power of the hydraulic system...
So basically I’ve got a 3 phase motor that I’d like to use to hook up to my cable stripping machine.
The motor was salvaged from an old site and I know it works. I know the easiest way to connect it up to a single phase supply would be to use a VSD but those are expensive. I was wondering if...
I am installing a micro-brewery in our barn in France; as you can guess that, means that I am a brewer, not an electrician :-) I did 'fess up to being a DIYer when signing on.
The brewhouse runs on 3-phase, both for the 12kw heating elements and for the pumps. All use a delta configuration i.e...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.