hi every body.
need to make connection of a schneider contactor LC1D40A with schneider RM17TG20 phase control relay.
need to how to wire between these two to make the relay will trip the contactor when single phasing happens in 3 phase system.
schematic diagram will difficult to understand...
Muhammad Abid
Thread
connection
contactor
control
diagram
phase
relay
schneider
supply
Hi
Maybe im over thinking this but need to connect a UPS system to a control panel, the problem is the ccts i want to connect to the UPS are split & all the neutrals are all connected to a single busbar connection unit at the moment which is all normal, but i need to connect a UPS to power...
So I was doing my usual morning browse this morning, and I have no idea how but I ended up reading a load of threads from years ago about the Dual Appliance Connection Units - it left me with a question that I couldn't find an answer to within those threads, and not wanting to reopen a 3 year...
I have this boiler:
Ravenheat - CSI 85 combination boiler - atmospheric combustion - high efficiency boiler
~ If link does not show, google Ravenheat CSI 85 Combination Boiler - Atmospheric
The website says, under Technical Data, that the boiler is 3 amps.
My previous electrician...
Hi All
What method do you use for earthing armoured to armoured on a platic 3 phase rotary isolator? Assuming I will have one armoured on top of the isolator and one on the bottom.
At the moment I use the banjos and on the inside of the isolator using an m6 bolt I'll lug the earth cable and...
I'm stumped on this one. My mate has a two way garage board in his garage. Circuit 1 is lighting, circuit 2 is 3 sockets on a radial. Lighting works fine. Sockets trip main RCD in DB when switched on. 3 sockets are now disconnected. Tried to reset 16A MCB (for radial circuit) and still trips...
I had a house alarm which calls my mobile when activated installed a year ago, the guy who installed it is in New Zealand until February and I can't get hold of him.
The landline phone stopped working, I opened up the connection box for the telephone line in my garage. Some of the cables came...
Re the above, anyone had recent experience of the above, not switching off (switched fused connection unit, obviously!). I've had three recently with the same fault. I emailed BG tech, who provided a prompt response advising no known bad batches/ problems, but willing to investigate if I or the...
could anyone give me some advice on connection of a odyssey 1 bell box to a paragon super alarm panel.
odyssey connections are,
A 12v
B Bell
C tamper...
Hi All,
Just look for a quick solution so I can complete my installation of the nest thermostat in particular the heat link.
from the image attached I'm seeking your help to understand which terminal:juggle: I should attach the call-for-heat from the heat link box for the SPDT relay.
Your...
Hi All,
Many thanks in advance for any advice, I know this is the place to ask:blush5:
Basically I am a 'consumer' who's having a pv array fitted and I want to check what the contractor's intending to do. I built my current house so I don't want it going up in flames! Unlikely but I'd rather...
dw89
Thread
advice
being
connection
inverter
please
power
setup
solar
urgent
Hello, boilers and thermostats are not my strong point. Can do following the manual, but unfortunately Hive model is not mentioned in the boiler manual...
Been doing new electrics for a kitchen refurb, customer brought this new thing and I got a bit stuck on it.
Got some pictures from both...
Hi everyone. My name is Tim and I need some help. I am looking at a motorised pack I am using to clean windows. I want to add a variable resistor, I think they are called potentiometers. I am wondering though, where should I put it and what value should I get? I think maybe 100 OHM?
Hope the...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.