When I was commissioning I tested between active and earth and got 0v.
Pulled the gpo off the wall and got 240 on the terminals.
Justly wondering if anyone could give me some insight.
Hello everyone. At home I change all wall switch with a sonoff t2. I didn't have a problem until I got to the bedroom. When I connected the light switch, and pressed the power button, the lamp turns on and off instantly. I came to the following problem. The wiring in the room is as...
Hey,
I'd like to ask for help, what should I use to avoid the side mirror turn signal warning?
I recently installed dynamic side mirror turn signals on my Audi A4 B8 2009, has been getting an error since (for both sides). I was thinking about installing a can-bus resistor kit on the sockets...
I’m trying to fit a new ceiling light pendant.
the pendant has a small connector with blue,brown and green/yellow wires.
however on the ceiling , there is just one basic pendant with 2 cords attached (blue and brown) so there’s no earth.
There is no ceiling rose l,think when they installed...
Hi guys, hope you can all help.
I'm moving house soon, and got a few jobs that I need doing. I'm looking at doing them myself (if possible) to save a bit of cash and get done in my own time. I'm not a spark, but have always doing little bits and bobs of my own so am comfortable, however I dont...
I was attempting to install a ceiling light in my living room. The house has old cloth wiring. The box I was hoping to tie it into has two switches: One was for my porch light, and the other was for the outlets in the room (not "switched" outlets, mind you- the switch turns all of them on or...
Hello,
Looking for some assistance with installing a dimmer switch in my basement. This is the only switch that controls the lights and there are two sets of black/white wires and a ground (see picture below). The capped black/white wires on the top in the picture below does not have any...
Good day to you.
I want to use a large walk-in closet as an office space. There is a light switch in the closet that I would like to replace with an outlet and switch combo. There is no ground inside the box. There is a capped neutral. The breaker is 20 amps.
To protect my devices (computer...
I've just repaced my hotwater and central heating progrmmer with a Hive active heatng and hot water thermostat. It's all working but the thermostat is still connected, I've turned it up to full so it's always calling for heat but I want to put the Hive thermostat in its place so need to...
Hi all
I’m installing a dimmer but the current set up is really weird:
The current switch has 2 live wires (the black ones) which both go into the same connector
this is the new dimmer but No clue what to do
Hi. I have installed a 5/8" earth rod but am having issues with the plastic box cover that sits on top. I purchased one from TLC but it seems too small to fit properly (see photo)
Also is there a specific gland to use where the 6mm2 earthing conductor exits the box? I don't want anything...
Ok I have a room that I’m putting a ceiling fan/light in where there wasn’t anything previously...I want to grab the power from a switch that runs the front porch light...I have tried various things and have looked on various YouTube vids...can’t seem to get it working ...I have a double switch...
Dear Friendly Electricians, I am an IT specialist. I am currently in a sticky situation. The company I'm working with is a digital advertising company. We have LCD screens to display ads. They asked me to install a timer on the screens. So they turn off during the night when the mall is closed...
Hi all,
I’m new here and after some advice on a sub main circuit
I have a 3 core SWA feeding a log cabin from a house. The house has an existing TT system and I’m just wondering what the best way to supply the log cabin would be?
What would I need up front to protect the SWA, I’m presuming a...
Hello! I need to install 2 new outlets in my living room — an 1887 brick home that we are gradually remodeling. I don't want to do any surface mounted boxes b/c of the historic aesthetic. So I see my options as:
Floor outlets recessed into the hardwood floors, or
Wall outlets recessed/chiseled...
Hello all,
I am trying to install three new light fixtures (hanging lantern type) that will hang from the ceiling of an outdoor covered porch.
The fixtures come with a cross bar that has preinstalled mounting screws with the threads pointing downwards. These threads are intended to go...
Hi
I'm installing an FIA battery cutoff switch into a Megane R26 Race Car. I have no issue with the main battery contact and the resistor install. I need an a way of stopping the engine because just cutting the battery will leave the engine running from the alternator. I'm looking for an easy...
I'm about to start pulling in the data cat 6 cable from the loft down to every room. I plan to have a switch in the loft which will then be connected to the router.
My question is about cable routes and boxes. Iv only ever seen data outlets either surface mounted or in recessed in stud walls...
I have LEDs under wall cabinets and in the bases of plinths to provide floor lighting. All looks good until you look inside or under the units. The required 12v drivers (power units - 240 to 12v) are free to float around and the very small twin flex to the LEDs themselves is difficult to fix and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.