Type of drill to get?

[Chriel90]

I’m new-ish to the trade and going to be working on site in a new build block of flats as an Adult trainee/apprentice, I’ve been told to bring my own drill but not sure what type to get? My site experience is little so I’m guessing I’ll be doing a bit of everything.

10v/12v/18v? Combi or impact? I’d really appreciate some feedback if anyone has been in my position or a seasoned site worker and can recommend what to go for

 

[suffolkspark]

I’m new-ish to the trade and going to be working on site in a new build block of flats as an Adult trainee/apprentice, I’ve been told to bring my own drill but not sure what type to get? My site experience is little so I’m guessing I’ll be doing a bit of everything.

10v/12v/18v? Combi or impact? I’d really appreciate some feedback if anyone has been in my position or a seasoned site worker and can recommend what to go for

18v combi, imo makita still to me seem a balance of price and quality, and common, dont get the bottom model get next one up if on a budget to start out. Selection of drill bits, masonary, metal, wood spade bits should get you started. An impact driver is handy but not essential, an SDS might be but depends what your expected to do.

 

[timhoward]

Yes. 18v combi, 2 batteries. There’s always some offer on at Screwfix and Toolstation. Keep a close eye on it once on site as it will look shiny and new!

I’d have thought you’ll mostly be drilling wooden joists and stud work to pass cables through, and blocks to attach back boxes. So wood auger bits and at least a couple each of 5.5,6 and 7 mm masonry bits for red and brown rawlpugs.
One day you’ll want an SDS drill especially if you are drilling bricks a lot, but new builds are usually made of cheese….

 

[LukeD]

Dont dismiss the Erbaeur stuff from Screwfix. Far better in use than many would believe

 

[oscar21]

Milwaukee, we've had a selection of drills from different manufacturers over the years and everything only ever lasted a couple of years at the most except the milwaukee stuff, we've still got a working 18V SDS that was purchased in 2014 and it gets abused on a daily basis. One of the combi drills has just packed up and that was purchased in 2016 and the multitool we have thats still going strong was bought in 2018. I think one of the impact drivers we have is nearly as old as the SDS as well.

Obviously some of the older batteries are toast by now but compared to some makes the genuine milwaukee batteries are cheap as chips. We've have several chargers blow up though but they are only £30 to replace.

 

[pc1966]

If I had to buy just one power tool, and had the cash to hand, it would be this sort of thing:

Milwaukee M18ONEID2-502X M18 One Key FUEL 1/4" Hex Impact Driver

Milwaukee M18ONEID2. 18 volt cordless bluetooth 1/4 inch hex impact driver. Compact with fast screwdriving speeds. The Milwaukee impact driver for self tapping screws into sheet metal. UK equivalent for US Milwaukee Tool 2857-22. Milwaukee 4933464092.

www.bigredpowertools.co.uk

I got the drill & impact set but it is the 1/4" hex drive impact driver that works great for drills to 12mm and for hole saws for 20mm/25mm. Be weary of using it on screws and small bolts as it will break them even on minimum setting!

Plenty of other good tools out there so don't ignore the other suggestions, but I'm really impressed with this one.

 

[nicebutdim]

Milwaukee, we've had a selection of drills from different manufacturers over the years and everything only ever lasted a couple of years at the most except the milwaukee stuff, we've still got a working 18V SDS that was purchased in 2014 and it gets abused on a daily basis. One of the combi drills has just packed up and that was purchased in 2016 and the multitool we have thats still going strong was bought in 2018. I think one of the impact drivers we have is nearly as old as the SDS as well.

Obviously some of the older batteries are toast by now but compared to some makes the genuine milwaukee batteries are cheap as chips. We've have several chargers blow up though but they are only £30 to replace.

OP is starting work as a spark, not a plumber.

 

[rewireIT]

If you can only get one, get an 18v combi.

If possible, get both combi and the 18v impact driver together. Combi for drilling, hole sawing, boring, all that stuff, impact for screwing. It's too much of a ball ache changing bits all the time so both is best.

 

[pc1966]

If you can only get one, get an 18v combi.

I got the combi & impact set, but found the drill hardly gets used at all:

Milwaukee M18FPP2A2-502X 2 Piece M18 FUEL Power Pack

Milwaukee M18FPP2A2. Combi drill and 1/4 inch hex impact driver Milwaukee twin pack power tool kit. Generation 3 FUEL. Milwaukee cordless brushless drills and impact drivers combo kit. UK equivalent for US Milwaukee Tool 2997-22. Milwaukee 4933464269.

www.bigredpowertools.co.uk

The drill is good for bigger hole saws, can work with smaller masonry drills, and it is more precise for accurate drilling as the 3-jaw check centres traditional bits better then the hex-shank style, but in most cases that is trivial. Also hex shank drills are typically only made in a few sizes so you might need to use normal twist drills for specific cases like pilot for hole tapping.

If possible, get both combi and the 18v impact driver together. Combi for drilling, hole sawing, boring, all that stuff, impact for screwing. It's too much of a ball ache changing bits all the time so both is best.

The hex-shank drills are excellent for that quick change, and the impact action works well for larger drills or the likes of the Armeg hole saws.

Only thing is the hex drills cost more and are not that great in terms of lifespan, but factoring your time, etc, they easily pay for themselves in convenience.

 

[rewireIT]

I got the combi & impact set, but found the drill hardly gets used at all:

Milwaukee M18FPP2A2-502X 2 Piece M18 FUEL Power Pack

Milwaukee M18FPP2A2. Combi drill and 1/4 inch hex impact driver Milwaukee twin pack power tool kit. Generation 3 FUEL. Milwaukee cordless brushless drills and impact drivers combo kit. UK equivalent for US Milwaukee Tool 2997-22. Milwaukee 4933464269.

www.bigredpowertools.co.uk

The drill is good for bigger hole saws, can work with smaller masonry drills, and it is more precise for accurate drilling as the 3-jaw check centres traditional bits better then the hex-shank style, but in most cases that is trivial. Also hex shank drills are typically only made in a few sizes so you might need to use normal twist drills for specific cases like pilot for hole tapping.


The hex-shank drills are excellent for that quick change, and the impact action works well for larger drills or the likes of the Armeg hole saws.

Only thing is the hex drills cost more and are not that great in terms of lifespan, but factoring your time, etc, they easily pay for themselves in convenience.

I must admit for everything except drilling out for stuffers and drilling through joists i use the impact.