Recent content by SSE

  1. S

    EICR code re conduit

    Sorry I maybe didn’t explain it very well. There are earths at sockets & switches through the twin CPC’s yes. What had been noted was that now that the new boxes weren’t attached to the conduit like the old now defunct boxes were there was cable passing through unearthed conduit.
  2. S

    EICR code re conduit

    Have been asked to do remedials on an EICR that was carried out a year or so ago by another electrician. Curious to know what code you would give for the following. The system used to be conduit & singles but was rewired in twin at some point. By the looks of it the conduits were cut at top &...
  3. S

    Wet UFH/ Radiator system

    Thanks for the replies. I’ll see what kit the plumber has & take it from there.
  4. S

    Wet UFH/ Radiator system

    What’s the best setup for a system that has a heating system with existing radiators but a wet underfloor heating system is being added to a new extension. I will need a 3 channel programmer I assume? The plumber mentioned having it on all the time but just working on/off the independent stat in...
  5. S

    Advice needed on customer

    First of all thanks for your help, good to get different views. Panic over! They’ve decided they will go ahead & get the work done. They said they weren’t against getting the board replaced they just thought the extra work would involve running 10mm earth through lobby where there’s laminate...
  6. S

    Advice needed on customer

    Sorry, forgot to reply to the other parts. Building control not involved no. I billed the customer for the other electricians work then paid him. I could swap the main switch for an RCD main switch as there’s only 4 circuits, this would keep the price down but I’m no keen to have the whole house...
  7. S

    Advice needed on customer

    He did test the circuits he worked on. The problem is the lack of RCD protection which I was hoping to change the following week.
  8. S

    Advice needed on customer

    Yes I get that you’re not meant to energise without protection being up to scratch. The problem being the kitchen had to get ahead as the kitchen firm had it booked in that week, I’d hoped to be back the following week to swap the board over. There was no new circuits added, just a few extra...
  9. S

    Advice needed on customer

    Priced to do kitchen electrics & mains board upgrade for someone a while back, they accepted my price. I explained that the mains needed changed as there was no RCD protection & prior to upgrade I’d carry out an EICR on the installation & if any C1 or C2 observations were made these would need...
  10. S

    Solar Panels supplying new build

    I’ve not been out yet but he says the inverter is connected yes, he’s been using it to power the caravan he has been staying in whilst building this house. He has an isolation switch that feeds a supply cable to the house but he says it’s turned off just now. He says there’s 230v at it but he’s...
  11. S

    Solar Panels supplying new build

    Should have also said he’s done the solar side if things, inverter etc & run the supply cable, just up to me to do all the consumer unit work.
  12. S

    Solar Panels supplying new build

    So...who has experience in this on here?? Not me for sure. Basically roughed in a new build for someone, was told he was haggling with the local authority over the price for putting power to his house, it's in the countryside. So I basically kept plodding on, got it all just about done, fitted...
  13. S

    Commercial pizza oven part

    Furnotel it says on the front. The below is the model number:
  14. S

    Commercial pizza oven part

    To be honest I’ve no idea, there’s no manual, looked for one online but can’t find one. Element is fine. So, it’s a double oven, each oven has a top & bottom element, the one that wasn’t working was the bottom oven bottom element, it gets hot for a minute, then says HHH & starts cooling. So I...
  15. S

    Commercial pizza oven part

    Any idea where to find the following part? The bottom element that it controls is not holding the heat & temperature dial is showing hhh.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Electrical Blog
Contractor Forum
DIY Talk
Electrical Advice | Electricians Blog
Tiling Tools for Beginners
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock