I was wondering if someone could assist me in determining whether I can replace my current 3-way switch configuration with an Enbrighten smart switch setup. I have provided photos of everything relevant.
The first switch box, which has only one 14-3 cable entering it, is depicted in an attached...
I have a light that does not get used and I want to put an outlet where the switch is. The light switch only has 1 blk wire and 1 wht wire on a 2 terminal. Switch that are mounted on the same side of the switch. How can I make this switch into an outlet?
I took a light down to put up a new fixture and now the light goes on but the switch doesn’t shut the light off. The power only stays on so I am quite confused. It is a 3 way switch. Both switches will not turn the light off. The wiring “appears” to be 14/2 to fixture and 14/2 out of fixture...
hello
soooo...😅 i recently changed all the light switches in my house. now i saw a video that showed the 2 tiny wires inside the switch should be connected to the "in" and "out" thingies. BUT, before installation, i stick them in a power outlet (witch has a phase and a zero obviously 😎) and saw...
Hi All, I have 24 volt landcruiser and have purchased a battery disconnect switch which I would ideally install on the negative terminal of the second 12v battery. The switch however is quite tall and I think its going to hit the bonnet when closed so am wondering if its okay to install the...
Hi guys, first time posting, please bare with me! I have an old test chart as shown in the pics that i would like to get running. Everything lights up seperately, the bit at the top/the red and green rings/the white rings/the line of letters at the bottom/the hole at the bottom used as a light...
Hi, I recently installed a smart light 2 gang 1 way smart switch. The two lights in question turn on. However on one of the 2 way lights I have spotlights and only one spotlight out of 4 comes on. Previously all 4 turned on. Any advice?
HI everyone I'm getting 255 volts between live and earth natural to live on a live lighting circuit fed from 6amp rcbo ,
When switch off I'm getting 59volts between live and earth
Natural to live 59 volts
Any idea why
Hi,
The wiring for my lights have multiple COM wires in most rooms, which are a pain to screw into the COM part of the switch. The switches that were fitted when I moved in work fine, but I purchased a smart switch which has slightly different sized screws / screw holes etc, and I can only seem...
Hello,
I wish to replace the old 2 gang switch pictured, with the smart switch pictured.
Am I right in thinking that all 3 reds wires would need to go in L.
Then the lower left black wire can go in L1.
And then the pair or black wires (from the bottom right) can go in L2?
Many thanks.
I've a light fitting that's controlled from a Whitecroft absence detector PIR and a wall switch. The way it works, is the Retractive wall switch with turn on the light by activating the PIR but then only turn off by the PIR’s duration or 10 minutes without absence. I’ve had to replace the PIR...
I have installed a number of 120v smart light switches and smart bulbs which I have set up on a schedule via an app. I would like to add another smart light switch for a light fixture that has a 120v to 12v transformer inside the light fixture, lighting six 12v (previously halogen) currently LED...
Hi guys
I have a homemade arcade machine that houses a PC that I currently switch on from the mains - this is connected to an internal smart extension with the master socket conncted to a PC. Thus the PC controls the power to the lights/monitor/amp etc. (there is a secondary on/off switch...
I am replacing a 3 gang switch with a modern one. All the wires going into the switch are the same colour. I have labelled which port each wire came from (eg L1 top left) but L1 L2 etc do not correspond with the new switch (L22 L31 etc). Advice gratefully received.
Hi,
With respect to the cooker switch only. If I moved it 400mm to the left by extending the T&E from its original position using crimps, then tile over the original back box, would it satisfy regs by maintaining the modified circuit within the prescribed zone (assuming all other rules are...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.