Discuss Exploding halogen lamp in the UK Electrical Forum area at ElectriciansForums.net

S

showerman

Hi all , not been on for a while . Has anyone had problems with
the low energy halogen globe lamps shattering whilst in use .
A customer of mine has had one blow and was very frightened
by this and asked me to check to see what had caused it .
She had three of these fitted in a light fitting , open shades , above
her dining table and one literally blew , with fragments of glass
going all over the table and her . Fortunately she was not injured
but was well shook up . I checked out all the obvious things like
voltage, condition of lampholder etc but all seemed ok , the other two
I have removed and I have replaced them all with standard tungsten
tungsten type because she is afraid it might happen again .
The halogen lamps appear to be unbranded and I have suggested I fit
replacement lamps from a known manufacturer .
The lamp that blew was a 28watt BC globe , any thoughts ?
Ken.
 
Hi all , not been on for a while . Has anyone had problems with
the low energy halogen globe lamps shattering whilst in use .
A customer of mine has had one blow and was very frightened
by this and asked me to check to see what had caused it .
She had three of these fitted in a light fitting , open shades , above
her dining table and one literally blew , with fragments of glass
going all over the table and her . Fortunately she was not injured
but was well shook up . I checked out all the obvious things like
voltage, condition of lampholder etc but all seemed ok , the other two
I have removed and I have replaced them all with standard tungsten
tungsten type because she is afraid it might happen again .
The halogen lamps appear to be unbranded and I have suggested I fit
replacement lamps from a known manufacturer .
The lamp that blew was a 28watt BC globe , any thoughts ?
Ken.
yes..

lucky none of it landed in the soup...
 
If there are slight defects in manufacture of the glass envelope then entrapped air in the glass can cause pressure in the lamp and shatter that glass.
Liquid or dirt on the outside of a halogen capsule can create different temperatures over the surface that heat stress the glass and can cause cracking.
It is also possible that if the filament melts through the surrounding glass if the outer globe is not an inert atmosphere then the filament can rapidly vapourise and as the outer globe is not designed for pressure it could break, this is less likely as the outer envelope should contain the glass if this happens.
 
1[SUP]st[/SUP] question:
Who fitted the lamps?
2[SUP]nd[/SUP] question:
Were handling procedures followed?

If you had nothing to do with either, why are you bothered?
 
Hi all , not been on for a while . Has anyone had problems with
the low energy halogen globe lamps shattering whilst in use .
A customer of mine has had one blow and was very frightened
by this and asked me to check to see what had caused it .
She had three of these fitted in a light fitting , open shades , above
her dining table and one literally blew , with fragments of glass
going all over the table and her . Fortunately she was not injured
but was well shook up . I checked out all the obvious things like
voltage, condition of lampholder etc but all seemed ok , the other two
I have removed and I have replaced them all with standard tungsten
tungsten type because she is afraid it might happen again .
The halogen lamps appear to be unbranded and I have suggested I fit
replacement lamps from a known manufacturer .

The lamp that blew was a 28watt BC globe , any thoughts ?
Ken.

You have answered your own question there...cheap chinese junk. I remember a batch of halogen fittings years back where the supplied lamp exploded on first switch on in about 50% of the fittings,very embarrassing if the client was watching!
 
Yet again the perils of cheap lamps. This is going to get worse with all the cheap LED replacement lamps starting to be used. Most of these are probably going bang as I type this. Daz
 

Reply to Exploding halogen lamp in the UK Electrical Forum area at ElectriciansForums.net

Similar Threads

Hi all, Great forum with lots of advice read and greatly received over the years! I have a question here that I am hopeful somebody here can...
Replies
16
Views
1K
Hi we are replacing light fittings in our home. Im confident with the fitting aspect, but have run into doubt in making the right choice of...
Replies
2
Views
520
I have halogen lights in my kitchen under the wall units, there are ten lights altogether bulbs are either 10 watt or 20 watt G4 bulbs ( not sure...
Replies
1
Views
761
Hey folks Apologies if my question is too basic. I am an Electrical Engineer but do not work in the field. I am looking for feedback to ensure...
Replies
0
Views
1K
Hi all, Im new to the forum and wanted to check something and maybe get some advice confirmation. Ive got halogen wall lights which use a...
Replies
6
Views
1K

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock