What to do with chasings

[sparkymcsparkf]

Hi guys,

I would be hugely appreciative for any input on this.

Basically my electrician did a full rewire and didnt use any capping or conduit, which as I understand is OK within the regs (as long as RCA protected which they are), but considered a bit unprofessional in the trade depending on who you talk to.

The electrician 'made Good 'in the chases for an extra 100 quid. I said about the wires poking out and he said it doesn't matter as the plasterer would be going over them. I think the plaster is usable, as such I dont need to have the walls replastered. So now I need to know what to do with these chases sonI can get the wires under the surface if the wall.

My instinct on the last 2 (dining room) is that I can chip away the existing plaster that he has used and push the wires back and go over it with a filler so that they sit properly in the chase. I'm a bit afraid of doing it though as I'm scared I may damage the wires. Also it looks like the wires have crossed over each other in the chase..is that supposed to happen/ok?

My biggest concern is the picture below where the wire is dropping from the ceiling (breakfast room) in the chases. No amount of plaster would set that right..it just looks like he hasn't used enough wire.

I am really at a loss as to what I can do. As far as I am aware as there are no regs broken I dont have the right to demand he comes back and fix it. But I dont know what I can and can't do.

If you guys could let me know how you would deal with this I would be hugely grateful. Any input at all...its honestly cooking my brain!!

Cheers!!

 

[Spoon]

Have you paid for the work?
Have you received an electrical cert for the work?
Is this the same electrician that did the work in your last post.

 

[sparkymcsparkf]

Have you paid for the work?
Have you received an electrical cert for the work?
Is this the same electrician that did the work in your last post.

Thanks for your response.

Yes, paid for the work and received certificates. And it is the same electrician from the last post. The work was done in January but due to lockdown and ill health I havent been able to look at doing anything until now.

 

[OnlQQker]

That will all skim over ok. Will need plasterboard anglebeads to form new corners though. Use scrim tape to cover up any cracks or week points in old plaster. Will also need 50/50 mix of pva (twice), the architraves will also need to come off around any doors.

I plastered over something a lot worse a few weeks back for a mate. The electrician had run so many cables including the 25mm consumer unit tails, none of it was capped.
He was a qualified electrician and signed it all off but I thought the whole thing was absolutely awful.
Anybody else and I would of walked away but this was for a mate like I said.

Once plastered you would never know what was going on in the wall, Just try and make a note so you don't put a nail through a cable when hanging a picture etc.

I'm assuming all the electrical works has been signed off?

 

[Red Tony]

Rough rough
And that's not a dog barking.

 

[Rockingit]

Pretty rough, tbh. I can only assume that the installer assumed he was being followed by the plasterer. As others have said, you're kind of stuck with it now but a decent tradesmen plasterer or decorater should be able to tackle it without too much hassle.

 

[Spoon]

As above, it looks rough.
Are all cables in the correct zones? See below.

 

[catdog1121]

looks like he has used bonding plaster which is great for first fill but you never get a decent finish. When you hired this guy was he the cheapest quote by any chance?

 

[LastManOnline]

Pretty rough, tbh. I can only assume that the installer assumed he was being followed by the plasterer. As others have said, you're kind of stuck with it now but a decent tradesmen plasterer or decorater should be able to tackle it without too much hassle.

Is it OK in UK to plaster over pvc/pvc that does, nt have some form of containment?

 

[Mike Johnson]

Unfortunately yes as long as the cable is RCD protected at the DB.