After some scoundrels robbed all my stuff I have had to get a new voltage tester. Two in fact. A fluke t150 and a a fluke t110. But unlike the ones I had these don't seem to have the ability to turn off the annoying bleeper. I have tried holding the light button for two seconds but it's no good...
Don't think I've seen this on here already. If it is then sorry for the duplicate.
Fluke have issued a safety notice on the 83, 87 and 88 series DMMs. A fault could result in a false no voltage reading. It was announced back in December but I've only just got to hear about it.
Hi All. My company have a brand new and supposedly unused FLUKE 6500-2 appliance tester, which i am unable to get into the settings, due to the ACCESS CODE, not being 9999 as i assumed it would be. I have also tried reset code of 1785 which was also suggested. But this is also not working.
I...
Is anyone selling a Fluke Microscanner2 or Idea Networks VDV? I’ve had the cheap testers but they are not that great. These are very expensive brand new.
Evening
Looking for software (or excel spreadsheet) to view data taken using Fluke 1735 power logger, Fluke software is ok but I'm wondering if there's anything else available?
Hi.
I have just purchased a fluke 1664fc MFT and it wont work. I can turn it on but that's it. It's completely unresponsive, I can't even turn it off. The only way to turn it off is to remove the batteries. I have tried replacing the batteries but this hasn't achieved anything.
Is there a...
Hi all, I have brought a fluke 43b to log a local farm to see how many amps they are using at maximum demand.
The meter gives 3 readings for each time interval. Min, max and average. I would understand if the readings were between 2 time periods, but don’t understand how you can have three...
I have a fluke 1653 which gives me a fuse error, but only when voltage is present. Done some research but not found anyone with the same issue... just wondering if it’s time to retire the fluke as I know it’s getting on a bit now...
just seeing if anyone’s had/ seen this before, I’ve tried a...
Rather than resurrect an old thread, to turn off the Beep on the Fluke MFT you need to hold the light button whilst turning on the tester, up on the screen comes "Beep off", but it does not work the Beep is still on, anyone have any insight into this, or is the Beep just turned off under certain...
Hardly used since purchase so in excellent condition.
I purchased when working on BMS panels etc, and came out of that section of work shortly after.
£200 I'll cover P&P
PM me
Took a gamble....
Purchased a faulty Fluke 1735 which appears to be missing a PCB inside the battery compartment, this PCB has AC input and USB socket attached.
If anyone has a Fluke 1735 (USB version) I would be glad to see a photo of the battery compartment with cover removed showing this PCB...
Hi all. First post.
Earth rod question. All work I've done, as a recently qualified DEI has been on tncs. Have a new job with TT. Old earth rod is buried under concrete steps. So I have installed additional visible 2 m rod and run new 10mm earthing conductor. I have a fluke 1662 and recently...
Before I put it on e-bay I have a Fluke 1663 for sale, complete with all the correct bits and working perfectly, comes with its Cal-Card for the last year, if anyone is interested, please make an offer.
Located in Kent.
It's not very often I praise a company but for once I will!
Almost a year ago I bought a 2nd hand Fluke 6500-2 from ebay. It was in almost unused condition complete with leads, barcode scanner, software etc. It arrived, I chucked it in the corner and I immediately forgot all about it. I was...
Hi, my fluke mft1653 has started erroring FUSE when testing voltage or any 3 lead test, I’ve changed the fuse in the battery box although this tested fine but this hasn’t made a difference.
Anyone had this before with their tester?
Thanks
Hi all,
I was testing a domestic premises In Ireland during the week for Continuity, pre-connection.
usong the Fluke 1663 megger, I had a small issue during the day related to the mA setting on f4.
During continuity testing you can set to 10mA or 250mA. My question is which is the correct...
Hi as per title, looking for a megger or fluke multifunction tester must be in excellent condition and fully functional.
Please let me know what you have.
Cheers.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.