Hi Guys
Changing my heating/water programmer and im stuck on the wiring ive gone from a danfoss to a Drayton and the wiring description is different ive had a go at what I think is correct but now when the heating is on and hot water off the hot water is still calling, and when I have just hot...
Hello everyone,
I will be completing my 2365 diploma level 3 soon and I have an opportunity to go and do the 2393 level 3 & 2392 level 2 as well.
Would this be a waste of time and money or should I do them anyway?
Kind regards.
Hi Guys
Forget to take cover off on last visit, back there Tue and need to sort some RCD protection.
Will this rcbo fit in this 'older starbreaker' DB ? couple pics attached
Thanks Sy
Howdy, I'm looking for help with my plan to install an extra internal double socket and an external double waterproof socket to my garage.
I believe its a radial circuit at the moment, with mains electrical supply coming from the house to a fused circuit board, 30A fuse to current double...
Good evening everyone
Can any help or give me some advice please on measuring bending galv conduit.
My question is bending long 3m lengths.
Say for example you need to bend a full length. 400 mm to back of bend. If you insert measured end first into the former obviously you can bend it to 90...
not to sure on how to find the wats for the power cable calcs could anyone help me its for a ring with 3 Dubble sockets on
DB05-3L2
cable size: 2.5mm
temperature rating:90°c
total demand
32a
29.125m
Design current
w/230
lb= 0.547A
Ambient factors
1 cable
Ca=0.91
Cg=1.0
It=design...
Good afternoon
I have recently had a bathroom makeover and had the existing shaver socket removed as I purchased a cabinet with socket enclosed. However, my oral b toothbrush 2 pin doesn't fit into thr 230v 2 pin socket in the cabinet whereas i had no issues with the previous socket.. I'm not...
Hello everyone,
I'm not sure I'm in the right place but I was wondering if anyone knew what that thing was (see picture)?
It's on the wall above my immersion boiler and is connected only to a thermostat (but is not connected directly to the boiler).
I'm a renter and never noticed it before and...
We have a tribune water cyclinder powered by an old version of the horstmann electronic 7.
We haven’t had hot water for a day or so now and wondering what I can do?
There are 2 electrical inputs to the cyclinder and the lights on the socket are usually off. I pressed boost and I saw one of...
Hi, I have 2 hallway lights that switch on together (used to before I got my hands on them). I am trying to install 2 spot lights. I have added pics of my wiring, which does not work. Pic1 light switches on but wont switch off, Pic2 light wont switch on. Some wires have coloured tape so I have...
Hi there,
I’ve hired a marquee for an event next month but am a bit lost on how to power it. There are 2 sockets 50 metres from the marquee and 2 sockets 80 metres from the marquee. We also have a 10kva generator, which provides over 7kva of continuous power and has 7 sockets.
We need to power...
Hi Guys
Got few of these coming up now... 1st fixes done.
Now the fun bit of 2nd fixes - bit of a head scratcher as none seem the same! 🤯
What I'm after help on is... I need to install a volt free relay if my switched live is 230v, which it is.
Does anyone have a link of where I could get a...
Hi all
Just about to carry out my first EV charger install at the end of the month and im filling out the DNO notification form
Im just stuck on the section about 'has this service capacity been verified by the DNO?'
I have undertaken a load survey and all in we are at about 80A so above the...
Long time lurker so this may be my first question. I am a qualified electrical engineer, but in aeronautics not domestic installations, and I may therefore ask silly questions. We have purchased a property that is unfinished, and where the electrician went bust before the installation was...
Two wires have disconnected when I moved a double switch for painting. Any ideas where they go please? I guess the live at the top goes into the com but no idea where the live at the bottom should be connected. I’m a complete novice so don’t want to do something that may be dangerous!
And the 1st thing I see is Smeg cooker tripping randomly.
So Here's My Issue Have Spent Numerous hours trying to talk to someone at Smug Smeg, Only to be directed to another dept of Smeg And yet another.
So the Issue, approx every 8 to 10 months . Oven rarely set to as high as 220. Normally...
Just been to view a house that I'm thinking of buying and I looked at the fuse box there seems to be three or four different fuse boxes I don't know what this even means??
'Looks' a nightmare, it's a rental investment so before I put an offer in I was hoping someone knowledgeable could offer an...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.