I'm your average DIYer and after advice about replacing a pendant light with a new flush metal fitting. I can fix the new light to the ceiling and the existing rose sits within the void of the new fitting without any clearance issues. Is it OK to leave it in place and wire the new fitting into...
Hi everyone
I inherited an old WW2 angle poise metal lamp recently. It works fine, but I'm not sure it's safe... the wire looks antique and is obviously just 2 cores.
I've thought about putting a new cable in it, and I'm guessing that it needs earthing as it's a metal lamp.
Can anyone advise...
I have just done an EICR... Havnt finilised coding yet.
Property is TN-C-S
Incoming oil to boiler... Copper oil line with pvc sheath, buried to metal oil tank sat on slabs on ground (it is not raised up) technical said it should be bonded.... Imo by bonding im taking pme potential out to the...
Hi,
Need a word of advice, how should I run supply to two metal sheds that are located about 20m away from the main DB. Should I run in SWA with 10mm bonding and as separate circuit to each shed or through sub-board adjacent to them? What IPX of switch and lighting should be, I'm expecting some...
Have things changed and I missed the memo.
Let's start by saying I'm a fossil. I was trained the old way, were u went with a mate and went to night school and day release. Anyway, was on a domestic fault for a mate of a mate. I rocked up, kitchen ring tripping. Asked any recent works, holes...
I'm looking to change ceiling light - from Ikea, its metal but there is no earth on new light connectors...i thought any metal light needed earthing?! The light is class II double insulated fitting so would that be the reason for no earth on light connector?? Will this be safe to fit with no...
Just been discussing this story, apparently some metal play equipment was giving people a shock, close to overhead powerlines and a transformer...
a small mention of dry condition, wondering on the cause? could it have been acting as a sort of rod and picking up some sort of fault via earth?
Or...
Can't seem to find any standard circuit diagrams for sequential reversing starter. The metal detector conveyor has manual mode and automatic reversal mode. Need to prevent the conveyor from going backwards during false signals or anything else while the conveyor is standstill. It should reverse...
Evening all.
I may have to fit a weatherproof junction box to a hollow, round metal pole.
The junction box will be around 20-30cm from the ground and 2 x SWA will enter from the bottom (CW20). 1 x rubber flex will leave through the back of the JB into the pole and up to the top where the light...
I have a couple of lights on a circuit that does not have a CPC. The light fittings are plastic but they have a metal trim that screws into the plastic body.
I wonder if anyone can advise me if these are deemed as safe considering the main body of the light fitting is plastic and the metal trim...
Hi all,
I am hoping someone has already had this problem and can suggest a solution.
Last minute decision by client to have an electronic release on a door means we have to mount the power supply (bell systems 340c) on the wall in a public space so it needs to go in a metal enclosure.
PSU...
Obviously bs7671 governs us in our electrical trade, and to the 18th we will need to use metal clips in all areas where cables are surface mount. So do data/cctv engineers have to use metal clips ect to prevent from premature collapse and who governs them to do so?
Anyone know if there is a conduit strap available in UK market similar to this one:
One Hole EMT Conduit Strap, Steel, 1/2 in. | Garvin Industries - https://www.garvinindustries.com/hanging-and-support/cable-conduit-surface-mount/emt-one-hole-straps/ohs-50
I'm thinking for 20/25mm pvc conduit...
greetings :)
I’m taking a spur from a ring final.
A fused connection unit will be controlling the spur.
FCU will be mounted on a metal backbox flush in a brick wall.
I’m planning on using a junction box to break into the RFC, and taking the spur cable to the FCU.
My question is, do both cables...
I was just reading an interesting post about the 18th when the above was mentioned. there seems some debate about this. I initially thought that the idea of prohibiting the use of them was stupid, but I'm not sure now...
Anyone know of any clips that'll meet the expanded scope of new regs concerning clipping cables (not just trunking only clips). Have used D-Line ones just wondering if there were other options people had tried (obviously there are other things you can use other than clips, but my question is...
Scenario encountered:
New submain looks to have been taken from a PME supply in 4c 10mm SWA with no copper earth to a external metal feeder pillar.
The SWA has been glanded into new metal clad DB within the feeder pillar effectively incorporating it into the PME supply. A Earth has also been...
I hate metal blanks there I said it I simply do not see the point the cover should stay closed itself and if there were an internal fire the mcbs would melt and the fire would get no further than the metal lid what about earthing are you supposed to drill and bolt an earth onto the blank? Scrape...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.