tamper

Recent contents Top users
  1. shurbra82

    Help I removed Switchboard tamper tags

    Hi all, I’m looking for advice I removed the tamper tags on my three phase power mains to install a new circuit breaker. It disconnected the smart meter for 5 minutes to make the change. I only found out now it’s highly illegal to remove the tamper tags. What can I expect to happen 😞...
  2. J

    Texecom Premier 64-W. Faults preventing arming of the system.

    Hi, My alarm system is a Texecom control unit (Premier 64-w) + Keypad + Sounder, and is using the wired zones 1-4 only, with no additional add-on's yet. I have 2 faults being reported by this alarm system that is preventing testing & arming the system: 1) EXP 1,1 Tamper 2) Zones 1, 2, 3, 4...
  3. M

    Texecom Veritas alarm Tamper light

    Hi, just wondering if anyone could help me. I’ve just installed a texecom Veritas alarm in my garage at home and can’t seem to get rid of the tamper light at all. At first I was getting red lights on all my zones Aswell as tamper. I then linked out all zones which got rid of the red zone...
  4. J

    Optima xm6 alarm and tamper prob.

    Hello. Could someone tell me what is meant by "linking out" say, as an example tamper circuit wires on an Optima xm6 alarm control panel and how is it done when there is a prob. Is it just removing the two relevant wires, connecting them together and putting a small metal link in the...
  5. C

    My Veritas R8 alarm went off when not set showing Tamper

    My burglar alarm went off last night when it wasn't even set. When I went to Keypad it was showing TAMPER with a Red light. I could not silence it either with the keypad user code or Engineer code and had to take the battery out of the control panel to silence it. Today I went round all the...
  6. Gnasher

    Texecom Premier Elite. EXP 1,1 tamper fault.

    Good morning. Fitted a texecom premie4 elite 64W over the weekend. Only one problem and that is I have a EXP 1,1 Tamper fault that I am unable to clear. Looking on various sites it points towards the commissioning jumper still being in the commissioning position. Checked this and the jumper...
  7. N

    Tamper Resistant Light Switch 15 amp Need Key

    Hello all. I recently purchased a house that has a tamper resistant light switch that controls a outdoor flood light. No one that I have shown these pictures to at Lowe’s or Menards have been to help find a key for it. Thank you for any help.
    • Need advice
    • Thread
    • 15 amp amp key light light switch switch tamper
    • Replies: 12
    • Forum: USA
  8. T

    Texecom alarm panel tamper light on and sounding off randomly

    Hi I wonder if anyone might have any ideas on the following. Random alarm triggering in small office. Two PIR detectors and two reed relays on two doors. The firm who put the alarm in have sent an engineer to inspect. The result being; There is nothing wrong with the system! I have been asked...
  9. E

    Galaxy Alarm Tamper Keypad

    Hi there. I have a honewell galaxy alarm. I am in engineer mode but when I enter the engineer code and press esc, it says checking for tampers. It then says Tamper Keypad 0 and I cannot get rid of this. It then returns to engineer mode again. It’s so frustrating!!! please, can anyone help...
  10. J

    intruder alarm tamper fault!

    Got myself a tamper fault on intruder alarm I installed on a refurb job I have been doing is only my 2nd wired system I have installed and had no issues on my 1st one! so would appriaciate any insights..... system is: Accenta Mini G4 Alarm Panel + LCD Keypad - 8SP399A -...
  11. yellowvanman

    Alarm sounds when deactivated

    Don't normally deal with alarms but a customer has asked me for advice and consequently I come here! Old system (circ 1980s) occasionally alarm goes off during the day when its been de-activated, type in their code and it stops and everything OK until the next time. Happening more regularly...
  12. G

    Honeywell Accenta G4 PIR wiring

    Hi, can anyone help. I am trying to install a Honeywell Accenta G4 with new PIR sensors. I am struggling to get the new PIR sensors to work correctly. The new sensors I have are IS3016 Passive Infrared Motion sensors. When I have wired previous PIR sensors, they have had 6 wires -ve +ve...
    • Gazza1972
    • Thread
    • accenta honeywell panel pir sensors tamper terminals wiring
    • Replies: 6
    • Forum: The Welcome Forum
  13. Leesparkykent

    Texecom premier elite compatibility

    Doing an unoccupied rewire on a house for a builder and part of that was running the cables in for a intruder alarm. finished of the snagging today and the customer has asked if I would mind fitting the alarm as they've been let down by the person who was supposed to do it. I had a look at the...
  14. Hellmooth

    Need help with alarm system!

    Hi guys, I've got an alarm panel at a job I'm doing, not sure what it is as don't really do much alarm work, I've attached pics though. I have a pir that I need taken out of the system, just wondering if anyone can help me out with how best to do it? I have pics of the panel, the manual and...
  15. T

    Honeywell ADE Optima Compact G4 will Not Set

    Hi Everyone I hope you can help me on this issue. I installed the above panel in my partners house and it has been working fine for 8 months until last night. She tried to set the system rom rkp and it just goes to unset on the LCD Display then back to day date and time display On the panel...
    • terrymac9
    • Thread
    • compact contact fault honeywell optima panel system tamper
    • Replies: 21
    • Forum: UK Electrical Forum
  16. A

    Veritas 8 intermittent tamper alarm

    Hi, I have an intermittent problem with my Veritas 8 system - the internal sounder goes off every now and then and the tamper light flashes red. I can reset it and the tamper light & sounder go off and the system functions normally for a while - sometimes for just minutes before the fault...
  17. H

    Alarm Systems

    I fancy reading a little on alarm systems - anyone recommend a good book that will teach me the basics?
  18. uksparks

    Pyronix alarm triggers

    Hi, I have and regularly install Castle Enforcer alarms by Pyronix. i have a question and hoping someone may know. how can I trigger an input from a third party device, so for example how can I close a relay on another device or put a 12v feed in to an input on my alarm? i want to be able to...
  19. L

    intruder alarm problems

    Hi I have been doing my first intruder alarm its a honywell accenta gen4 mini. I am only using 2x pir sensors 1 panic alarm, 1 key pad, and 1 sounder. The first pir is above the entry/exit door so I am not using any door contacts. once I set the system the pir's are picking up movement but not...
  20. M

    removing alarm sensor

    Hi guys. Just a quick one. Doing the electrical work on an extension and they used to have a garden shed with an alarm sensor in it. I want to remove the sensor from the system but wondering what's the correct way to do it. The sensor has a +,-, tamper and N.C in it. So do I just bridge out that...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock