Hi
My company recently required an electrician to install a new 32A 400V socket in our workshop. The guy who did the job, installed 32A, 3-pole circuit braker, type C and 2.5mm SWA cable, as he was confident to use the installation method reference 'E' in his calculations. The thing is, that...
Scalar6
Thread
electric
electrical
electricians
installation
method
these
wrong
Yesterday smelt a weird smell of burning/melted plastic in my bathroom after some looking about realised was the shower pull cord opened it to the the incoming live insulation completely melted an charred and the pull cord terminal melted shower was installed about 3/4 years ago but recent board...
hi there
after some advice re the above problem when just doing a simple like for like shower replacement, as it keeps cropping up. 8.5kw showers, 6mm2 cable protected via a 32amp MCB. now i would usally protect a 8.5kw shower with a 40a mcb on a 6mm cable (ref mthod c) . now i know a 8.5kw...
hi,
just needed a bit of advice.
ive bought a 10.5kw shower installed it with 10mm cable and a 45a pull cord. I cant seem to find a 45a legrand mcb anyway will it be okay to use a 50a legrand one?
thanks paul
Looked at a job today where the elderly occupants have the old rewirable fusebox tucked away high in a kitchen cupboard where neither of them can reach, or replace the fiddly fuse wire.
They've asked me to price up replacing the CU with a split RCD unit but would also like it lowering so they...
Hi
What is the installation reference method for flat T&E cable, with capping and buried in plaster, am I correct in thinking it is method C as all the others in table F6 (page 150) in the OSG refer to insulation?
Steve
guys whats your preference when fitting external accessories (sockets particularly)?
do you straight rear entry with cable and cake in silicone to prevent ingress
do you fit the masterseal cable entry grommet
are you a conduit man right through wall and into box
sure there is a couple others...
Hi, designing my first small installation which i will be using for my first assessment with Elecsa/NECEIC etc ( any thoughts on which way to go appreciated). Installation is in an oak wooden framed and mostly glass conservatory with instruction of no visible wiring please! The obvious way...
i was just wondering where do people buy there s type td rcd's from? there seems alot of different prices on line from 30 pounds to 80 pounds.
i have split load cu with two 63 amp 30ma rcd's on a tt installation, original rcd is 80amp 30ma so trips out when a fault.
could i use 80 amp stype...
Just trying to get something straight in my mind. I've been looking at the Electrical Safety Council's Guidance 6 for changing a consumer unit in a domestic premises. They say that if the customer does not wish for a full EICR then the pre-work survey required before the CU change should...
Hi guys.
I've been trying to organise abit of pat testing with a customer, and he's asked if I can show him a risk assessment, method statement, and my public liability certs... Now the final one is easy, but the first two?
He already asked to see my electrical certs (which you don't need for...
i done my 303 practical, and ive got 1 fault im not to sure the rectification method i got was correct
i found out that the immersion heater was dropping the ir between l-e to around 0.10 ohm
remove fronts on immersion switch and the fused switch, visually check to see if there any loose...
Hello, I am a new member here, so sorry if I did something wrong.
I have a circuit: The phone jack is connected to a microphone to detect the sound in an engineering workshop, when the level of noise is high current from the microphone pass through the diode to charge the capacitor C1, some of...
Hi all looking for method statements is there any good website you would recommend or any I could use.
Trying to get all my paper work in order.
Many Thanks
Hi guys currently doing a hnc and I am stuck on a question regarding the lumen method of lighting design. Ill post the question underneath-
A workshop is 40mx50m to be illuminated with 1000w high pressure mercury vapour lumnaires providing an illuminance at working level of 283 lux. The lamps...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.