Hello all,
I have a tail light for a '12 Ducati Panigale 1199 S, that I can't get working properly. The brake light / daytime running lights work fine through the factory connector. The turn signals are the problem, they do not work independently - they flash like hazard lights.
The tail...
I currently have a Myson thermostat that is no longer working. I have a Meross thermostat to replace it. I have attached photos of the current wiring and of the new thermostat. Could anyone advise on where the wires would go into the new thermostat?
I am installing 9 LED downlights each with an RGB bulb in (i will try attach pictures on them) - anyway I have been told that they need to be wired in a row. Like in/out - in/out in a ring pattern terminating at the last light. I am going to connect them to my wires where the old light fitting...
Been round to a house to quote to replace some storage heaters for new panel heaters and came across a strange (to me at least) way of wiring the old storage heaters via a contactor in the board, as usually I see their own off peak consumer unit which powers up at night via economy 7.
From the...
Hey everyone complete idiot here😂 can anyone please help me with what goes where if possible by these pics? There is one black and one grey wire, rest brown, blue and ground, cheers!
Hi All,
I have a terminal on the wall with 2 blue wires, 2 brown and a copper one (Photo 1), and I would like to connect a lamp which has 1 black wire and 1 white wire (Photo 2).
How should I connect them to make working the lamp?
Thanks in advance for your help,
Juan
Photo 1
Photo 2
Hi can anyone help me with this light switch? Photos of how it was wired to old switch but new switch is different with different names.
I’m confused to where the wires go?
Attached some photos
i had a 3 speed blow motor to an AC fan coil unit. I disconnected the wiring and installed a new unit and forgot how the wiring goes, i no expert and dont want to burn anything out...
from my electrical panel to the blower motor, I have a wire that has 120v, another wire has 40v, and a 3rd...
Baja wiring harness LED light help.
I've fitted a US Baja harness on my Australian FJ, but I need to replace the Baja harness switch setup so that I can comply with A.U requirements for forward facing L.E.Ds. Australian road law requires a forward-facing L.E.D can only come on when the...
I posted a month ago regarding a single phase motor + panel I have been given to try and sort following water damage to the panel.
The assembly is a single phase 110v brick hoisting motor and so needs wiring to allow reversing.
There is nothing to work back from as it was all disconnected but...
Hi my sparky has gone AWOL with just this to finish. The two black plugs are two rows of garden lights that are already installed. I would presume the top hole is for a switch to turn on and off and the bottom a fused spur maybe to get power but how does it all wire up. Because the job is small...
Anyone could recommend "best practices" for wiring methodology of 64 LEDs (each req. 10V@700mA)?
Including resistors, drivers, parallel/series, etc...
Part of the question is if these should be configured in an 8 x 8 configuration where each one bundle is a 4 x 4 series/parallel setup?
Drivers...
Hello, I’m need some advice on how a contactor is wired please and where the neutral go. I’m told it is connected to eco 7 and controls 3 heaters in a domestic flat. It stopped working after an electrician did something on a different circuit in the consumer unit.
The contactor is an Eaton...
Ok, can somebody please explain, with exact code reference and steps/reasons why this works.
MCA 37amps. MoP 60 amps.
Why can I land #8 on a 60amp breaker?
I know theres exceptions in Article 440. Is it in 440.4(b)?
I understand why it would make sense. Larger breaker for inrush. The MCA...
A question if I may before I dive in.
I have an old gravity fed CH system which thanks to members here in the past - works very well.
It has a Danfoss Randal 3060 programmer that has died.
I have the original installation docs for the programmer - and it shows 7 terminals plus the earth.
In the...
I've been having issues with my dining room lights flickering and light switches working intermittently. After taking off the switch covers, I didn't need to be an electrician to see stuff was wrong. There were exposed wires, red wires attached to black wires, black to white, and so on. I've...
Hi everyone,
I’m new here and I’m in the middle of doing some wiring and I’m a little hesitant.
Can someone confirm if this is correct please??
I’m putting in a new socket where there was one already. I’m also adding a switch which wasn’t here but when I bought this flat there were some cables...
Hi, so we have been living in a house that was built in 1880s/1890s, and we have had a few issues with the electrics.
I mean we live in a pretty cheap house and am quite aware that the reason we have these issues is because of that, but I would like to at least live safely!
So March 2021, our...
Hi,
I have a 2009 corolla sedan conquest 1.8 4cyl manual.
My lights have started turning off whilst driving especially high beam but not my fog lights. My reverse lights have also started to not work as well.
My radio aux has also completely stopped working and my radio stations are being re...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.