You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
cable run
A power cable is an electrical cable, an assembly of one or more electrical conductors, usually held together with an overall sheath. The assembly is used for transmission of electrical power. Power cables may be installed as permanent wiring within buildings, buried in the ground, run overhead, or exposed. Power cables that are bundled inside thermoplastic sheathing and that are intended to be run inside a building are known as NM-B (nonmetallic sheathed building cable).
Flexible power cables are used for portable devices, mobile tools, and machinery.
Some advise or views would be appreciated.
My supply is 100 amp single phase.
I purchased my property 3 years ago or so, the owner prior to the couple I purchased it from had installed a single external 32 amp socket near to the kitchen back door.
The cable to this socket is easy enough to...
Hi
I've got an new outbuilding that needs power run out to it, the building is very close to the house and the original plan was to run an armoured down the wall, in a 600mm deep trench and then up the wall of the outbuilding. I've marked the originally intended route on the image below, which...
Hi,
I’m an industrial electrician, so when it comes to DB regs and such my experience on them is a little limited.
I need 2 x 16A 3 phase supply and 4 x 230v 3 pin sockets which is intend to do as a ring however, the nearest supply is approx 120m away! Running this through a cable calculator...
Do you install new heating systems? Ever had a missing cable run between a boiler and a pump?
Using MAINSLINK - the pump overrun solution - you can avoid expensive cable runs when cables are missing between a boiler and a pump. When the MAINSLINK by the boiler has 230Vac live input, this...
Hi all
I'm looking for some help on a query I have.
I'm currently involved with a new build with the plan to fit Solar in the very near future, which I have never installed before or had any experience.
The plan is to fit a 3.4kw system and i wanted to put in the cable ready from where the...
Hello
I’m going to install a hard wired 230v security camera, incorporating floodlights, outside and above garage door onto brick.
An exposed expanded metal lintel (that is hollow) runs across the garage door opening. Outside it has a decorative brick facing. The brick is not load bearing.
I...
I'd be very grateful if someone can help with this.....
I've added a diagram to help explain. This is single cabling not a ring (I'm in France). All the cabling is underground which is split into 3 at a junction box by MCB's. There are 5 spurs above ground on the cable in question and each has...
Hi all. I have a couple of outbuildings which I laid cables to from the house. Both are about 130m cable runs away individually.
Just thinking about the time it takes for a RCD to "trip" - do I need to put RCD's in the distribution units? at the buildings? Also I presume it would be wise to...
Hi All, first time post so be gentle. My consumer Unit is situated under our stairs next to an outside wall. I currently have a 13amp two gang socket under the stairs, surface mounted. The boss lady now wants two further sockets situated near our front door on the same wall. Extending the cable...
Help brain has turned to mush.
A simple ring circuit 2.5 twin and earth.
can supply upto an area of 100meter squared, stated in IEE Regs. Right. (O yes please negate any correction factors that might normally apply).
And if i remember that is: 100 meters squared = 100meters x 100meters
simply...
Hi,
In a domestic new wire; before the concrete floor slab has been laid down; i am proposing to run the cabling for the ring mains.
I have been advised to use flexicon steel flexible conduit for mechanical protection and im using 2.5 T+E.
Question:
A) Do i run the conduits and...
Hi, looking for a bit of advice with regards to calculating costs and timescales for installing large runs - 300 mtr+ of multi-core cabling. To get an idea, the weight of the cable drum would be in the region of 450kgs.
The cable will be run over cable tray.
What I am asking is to get an idea...
Yooj
Thread
aus
bends
cablecablerun
cheers
installation
long
methods
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.