Been out the domestic game for a long time, but now having to rewire my own house.
Was wondering what the maximum cable length would be for a 1.0mm lighting circuit with 100w of leds?
Is the max cable length the ‘maximum’ length of r1+r2 from conumser unit - up and down switch drops - to the...
I live in Phnom Penh, Cambodia and people die here regularly by electrocution. There is no earth wiring in the buildings, just live and neutral.
I am a member of an expats forum and the question arises: Will using an RCD device offer any protection at all?
I understand RCD's will go off with...
I am abandoning an oven/microwave location that has an existing 220v 40amp (4-wire) circuit. I am leaving the wiring in place. I want to use the new counter space for a built-in microwave oven and coffee station.
Can I use one of the 110v circuits in the junction box for a 110v 20amp receptacle...
Hello Experts,
I had an electrician visit my place for some repairs and when looked at my recently installed main panel (photo attached) he said that the panel is not setup correctly. He said that 220V breakers are connected to 110V circuits within the house. Could someone explain what the...
We are currently renovating an old house after recently moving in. Whilst purchasing the property we received written assurances that the original 1920/30s wiring had been fully upgraded and subsequently tested.
After removing all of the downstairs ceilings, it is clear than new electric 2.5m2...
I'm in the process of renovating a house. As I go through room by room I am removing old plaster and as the cables are exposed at this point I figured I may as well get the wiring updated as I go. The ring main (~6 sockets) is currently fed from 2.5mm T+ E. Eventually I would like to have the...
Is it ok to run a 110 line off a 220 circuit? Specifically, I want to add a 110 outlet near my hot water heater and it would be convenient if I could use one of the hot wires along with the neutral and ground to create the circuit I should also mention that the 110 line will almost always be in...
What is everyone's opinion on taking a combi boiler supply off the lighting circuit? I doubt the boiler would pull more than 300 watts and with all the led lamps being used on the lighting circuit,I doubt it would come to more than a couple of hundred watts.A 3 amp fuse in the boiler spur would...
Had a bit of a ‘discussion’ today with another electrician.
Basically found a light switch in which the radial cable for a socket directly below (but about 3ft lower) passed through.
Other electrician said it was wrong and shouldn’t be done.
My take was that it is, at best, a bit of bad...
Hi there. I'm a DIYer. Just bought a house with a double garage that has just one socket in it; and it seems to be just a single spur direct from the CU. I want to put in more power outlets; and was wondering whether it's permissible to remove the existing socket, put in a 32a fuse/breaker, and...
Afternoon all. Bear with me on this one...
Despite having been involved in the electrical industry for many years, I'm only just about to embark on 2391 - its more of a personal endeavour than anything, having been very interested in inspection & test for a long time (I know, not everybody's...
Hi! I'm new here, so, please, be gentle...
Decided to add some extra features to my old and simple barn's electric system to make it safer and measure the consumption. It's a three phase 230/400 volt line. The neutral, as far as I know, is grounded at the step-down transformer. I don't have a...
Hi, I have completed a EIC for a garage DB2 with five final circuits (no problem there i think). But for the distribution circuit from house DB1 to Garage DB2 I have completed a second EIC for this alone. The questions I have for the distribution circuit alone are:
1) For the EIC 'particulars...
I have just been in the process of changing some old 12v halogen downlights in the bathroom for bathroom for mains volt leds.
My late father was a retired spark so know a little of doing some basic things.
The previous downlight transformers had been wired into a choc block which was just...
I work with someone who really isn't happy installing new circuits into plastic consumer units.
Sometimes he refuses to do it if the board in question isn't in a great state or if the existing wiring is spaghetti junction.
Obviously the regs state that it's fine to add if the board conforms to...
I'm building a "media wall" type structure, to house TV, av equipment etc, with alcoves each side lit by Led downlights and I'll be extending my ring main also as part of the build.
My question relates to clipping cables to the ceiling plate (2x3 timber) - is it acceptable to run 1mm T&E...
I have a 208v circuit that reads 208v across the leads on my meter; but when I connect a baseboard heater rated for 208/240v that works elsewhere in the same house it doesn’t work. Appreciate any assistance!
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.