i HAVE 240 volt wire feeding a submers water pump going down long hill.at bottom of hill is a junction box with 4 wire for pump on a dryer plug.rest of 4 wire feed plugs into it.for pump.i want to hook a 120 volt plug in at this point using the existing 240 volt 4 wire with 2 hots.can i do this...
cujiman
Thread
another
based
electrician
not uk
plug
qualified
volt
volts
wire
Hi I've got a question regarding volt drop.
When calculating volt drop to a 3 phase distribution board do I use 230v (11.5v) or 400v (20v)
The board I'm attempting to put a cable to is 75 meters away.
Design current 100A
From TABLE 4D4A Cable selected = 25 mm²
For 25 mm²: mV/A/m 1.75 for 230v...
I have an install to complete where I have to take a 100amps per phase three phase supply over 330m too power a new installation. The power at source is obviously 415v (give or take) however the rating on the machine at the other end is 400v (build in Europe somewhere). I'm currently having a...
gavin.sibley
Thread
cable
electricians vans
phase
power
supply
using
van
vehicle
voltage
voltage drop
volts
Can anyone help?
A customer has a light fitting in a bedroom (5 bulbs) which is switched two ways with a dimmer switch by the door and a switch by the bed.
He states that at some point he switched it on and nothing happened. He assures me they were working at some point before!!!!! He replaced...
iwire4
Thread
dimmer
light
switch
switched
voltage
volts
working
Just wondered if it's a no no to run 2 low voltage lights from one FCU
I have wired up sockets and lights to my decking outdoor accessories of course.
From my sockets I have spured of to a RCD FCU from this I have my decking spotlights.
So my question is can I run some LED strip lights to...
All,
I have my niceic inspection coming up soon and am a little confused about the requirements for a 2 pole voltage detector. According guidance note 3, a multifunction tester, multi meter or a volt stick can't be used which is fine, but what I want to know is if a clamp meter capable of...
I am checking an install and noticed the voltage between line and earth is 190 volts. I checked incoming supply voltage with the main consumer unit isolated and am getting 220v l-n and l-e when I switch cu on voltage l-n is 220 volts l-e drops to 190 volts I have disconnected all circuits and...
Morning gents, just a quick one. I've posted this already on the Solar PV forum but thought I'd add it here too as VD and cable calcs are always a good topic of discussion.
So I have a Solar PV system to install this weekend, its a 10KW single phase system on a farm. I'm going to be running a...
Just a quick one folk.
Do the voltage drop tables in the BGB apply for ELV systems?
I'm converting my van to a camper so I'd adding 12v circuits for lighting, water pump etc.
It's all going to be run in 3183Y flexible cable, can I use the VD values per mA/m in the regs, the same way as I...
Have just replaced my low voltage thermostat with NEST version.
Have moved the new thermostat by extending wiring with connection box (wiring is low voltage).
Is it safe to plaster directly over the connection box and wiring??
Cheers.
james.scott
Thread
connection
low voltage
thermostat
voltage
volts
wiring
How does earth fault loop impedance and disconnect time requirements change for 3phase 3 wire 230 volt systems where the phase to earth voltage is 133 volts instead of 230 volts?
Hi guys. Those who don't know me I have recently started on my own.
I am testing my understanding, re Volt drop. And trying to stick to one formula. But I'm getting mixed results.
My example scenario would be to feed a CU in an outhouse / shed.
The CU will feed sockets, lights and some form...
Been to look at a faulty socket on a rcbo and wont hold in, tried to test trip times etc but reading voltage on earth. Supply is tt, 3ph and 1 ph to a domestic property. Shared earth rod. Cant turn house off as belongs to separate person. So tested voltage at 3 ph db, 230, 400 v etc but...
Evening all..
I have just tested a cable that I had put in place myself for a smoke detector and I am only getting 28V L-N. I am getting 240V L-E.
When I first put it in it tested 240V. Since then the builder has been in and put the ceiling up, I'm not saying this is the cause but this is the...
Hi guys I've been doing a partial rewire. And I have taken a feed from a light that is fed, to feed a switch in a new extension. I wired up the lights and switch in the new extension but the light would not turn on. I measured the voltage at the light that's not powering up L-N and I'm only...
Jamie181191
Thread
earth
light
low voltage
readings
strange
tested
voltage
volts
Customer has been trying to use a dishwasher using Economy 7 at night, and its not working properly. Works fine during the day, Miele engineer says nothing wrong but the cause of the problem is a pressure switch that ends up with the dishwasher failing to heat the water.
Water pressure has...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.