button

Recent contents Top users
  1. S

    RCD won't trip

    Hi can anyone help. I have just done an extension to an annexe, using 3 core 1.5mm swa for the lighting and 4 core 2.5mm for the ring into a 2 way CED Garage Consumer Unit with a 63A 30mA RCD, 32A and 6A MCBs. Ze, Insulation resistance and continuity test came out fine testing with a Megger...
    • shovelhead
    • Thread
    • aus button faulty insulation rcd testing trip won't
    • Replies: 35
    • Forum: Australia
  2. R

    One hourcentral heating timer for student let

    Can anyone advise me on this: 1. Student house tennants always going out and leaving the heating on (home for xmas - heating full blast!) 2. Gas CH from backboiler heats water and house controlled through normal programmer 3. I want to have hot water permanently on. 4. I want to have a "push...
    • rjmaycock
    • Thread
    • boiler button heating house student through timer
    • Replies: 3
    • Forum: Central Heating Systems
  3. B

    Wrote nice long letter pressed button and it disappeared

    Wrote nice long letter pressed button and it disappeared no time left will do it again later.
  4. J

    Measuring earth loop imopedance Ze using FLUKE meter - settings??

    Guys (n' girls of course) I have just started using a 1653B FLUKE and when testing earth loop impedance Ze (ie. impedance of supply - tested at supply origin), I presume I use the 'LOOP IMPEDANCE' setting (line to protective Earth L-PE) using the Z1 Hi current setting, and NOT the 'Earth...
  5. S

    Panic button for soldering equipment

    Hi I do some electronics work. For safety sake I was wondering if there's a type of panic button I could use to cut off the supply off a socket which I'm going to install. It will be run off an existing double socket. Once this panic button is pressed the power should stay turned off until I...
    • swc
    • Thread
    • aus button equipment
    • Replies: 23
    • Forum: Australia
  6. I

    RCD ramp test

    Hi, just tested a fuse board: 1*main switch lighting circuit lighting circuit smoke alarm circuit ----------------- 1*rcd Oven Sockets Sockets Sockets Security Alarm Water Heater ----------------- RCD failed 1x with ?400ms reading (megger MFT) performed the ramp test and the RCD tripped at...
  7. M

    rcd not tripping

    hi to all i need a bit of help as i dont normally deal with 3 phase i have come to carry out a periodic inspection and carried out a rcd test on varrious circuits and it wont trip at 1x test the system has a old mem d/b with a rcd as a main switch what would cause the rcd not to trip out...
    • michufc
    • Thread
    • button canada circuits don't needs rcd replace tripping
    • Replies: 12
    • Forum: Canada
  8. R

    What does the Facebook Connect button do?

    f Connect button at the top of the forum home page - what does that do? I clicked on it and it wants access to my profile on FB. Did 'do not allow' because I'm not sure what/why it is doing this.
  9. N

    Like button

    I have pressed the like button a few times , and have noticed it says that i like the comments with a love heart , yes i may well like it , and its getting closer to valentines day but a love heart , why not a pint of beer or kit kat chunky or coffee mug lol:rolleyes:
  10. C

    i like button

    i like this feature, and i'm fairly sure its new, if not i missed that one big time! :D but i do wonder if the heart is a bit much??? :rolleyes::rolleyes: i mean guys i like you but i'm not sure i want to "heart you" :rolleyes::rolleyes: danny
  11. D

    Fluke 1651

    Hi Chaps thinking of putting in for a part P scheme and seen a Fluke 1651 advertised for £180 out of calibration is it suitable? Decent how much does calibration cost and how long does it last?
  12. E

    Megger 1553 help

    replaced my battered 1552 with a 1553 and have noticed that when carrying out a continuity test , with leads open >999 with leads joined get a valid reading, when breaking leads open again the reading stays and wont return to >999 and this i find very annoying? any ideas anyone? the lock...
  13. C

    RCD Trip Time

    I think I know the answer to this one - but could do with some clarification. 30mA RCD trips out at 51.8mSec on 1 times test & 38.7 on 5x Test values seem high to me - Domestic installation. Repeated the test 3 times just to make sure. RCD probably 11 years old and, of course, never had the...
    • chloebear
    • Thread
    • aus button rcd time times trip
    • Replies: 7
    • Forum: Australia
  14. L

    bloody door bell

    hi every one new build we done about 6 months ago, had a call to say that the door bell does ding but doesnt dong.... called in today, the chime is 8 - 16v got a 8v tranny which actually gives 10.5v. when push button is pressed the voltage drops to 7.9v but the ding just doesnt sound right...
    • lewlec
    • Thread
    • aus bell bloody button chime door tranny voltage
    • Replies: 10
    • Forum: Australia
  15. W

    inter connected smoke alarms

    hi guys, can some one tell me that if you push the test button on smoke alarms, are all the inter connected alarms meant to sound too. when i tried it today only the smoke alarm that i pressed sounded. all the alarms are inter connected.
  16. S

    How does a IR Tester work?

    Hi guys, 1st post, so please be gentle with me! I know how to use one but does anyone know how an IR tester actually works? I'm using a Megger 1502 and testing at say 500vdc does it actually apply 500vdc all the time you press the button and deliver 1mA for the whole time? And how long should...
  17. M

    push button time delay switches Arrh!

    hi there every one done a periodic on what can be only describe as a pre site constrution then lobed in place accomodation building for one of her majestys places etc. opened up a push button time delay switch thinking standard or conversion but no :eek: parallel using twin and earth...
  18. S

    Contactum RCBO won't trip during test

    Hi again, just considering whether I'm going crazy or I've got a duff RCBO. Perhaps someone will help me see the light either way. Quite prepared for the former! Installed it yesterday and when I got to doing the certificate I couldn't get it to trip. It's one of the ones with no earth wire...
    • Smugley
    • Thread
    • aus button contactum during megger rcbo sounds test trip whether won't works
    • Replies: 4
    • Forum: Australia
  19. M

    RCD manual test button

    Right folks i've got a problem. Fitted a 63A 30mA double pole rcd (protecting outhouse)which is being fed from 63A s-type rcd(in house). Tested rcd in outhouse-doesn't trip. Tried manual test button as well-doesn't trip. Re-placed it and tried again.Same as before. Am i right in thinking...
  20. Y

    fuses with a push button reset

    Hi, I remember at college I was told that if you see old resettable cartridge fuses (the ones where a button pops out) to replace them - but I can't remember the reasons why??? I just said that they no longer comply to my customer but what actually is the reason? I hate not knowing and talking...
    • YTSOxford
    • Thread
    • aus button fuse fuses number remember reset
    • Replies: 13
    • Forum: Australia

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Tilers Forums UK
TilersForums.co.uk
UK Tiling Forum
Tilers' Talk
DIY Talk
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock