The scenario,
Property has no bonding to gas meter. There is a 4mm T+E radial from the DB to an outside socket which is located 300mm from the gas meter (external meter). The 4mm T+E is housed in 20mm plastic conduit running along the external wall.
To prevent things looking a complete mess...
Whenever I’m on Instagram, I always see posts from sparks in the good old US of A, and whenever you see a conduit system install, there are always loads of individual conduits running alongside each other....do they not use trunking over the pond? Don’t get me wrong, it looks super impressive...
Any tips for cutting conduit to ensure a good finish? We're starting with it at College and I hate the stuff, I end up cutting to length fine but after touching up it's all buggered.
Unfortunately due to my cerebral palsy, my fine motor control is pretty shot, along with my ability to judge by...
Hello,
I had a question about the 3 foot supports after conduit body. I am running my EMT conduit around the fascia as pictured below. I don't want to do a 45 bend because i think it will be difficult to get the wired pulled through on my second story so i went with a 30 degree bend. My question...
I have been given a short length of Emt tube from America , which is basically their ‘go to’ produce for surface wiring.
It is thinner than our version and much easier to bend than our version.
I would say it’s not much thicker than copper plumbers pipe.
But imo offers good mechanical strength...
Hello!
I am setting up a smart home system and will need a neutral wire for the application. Some of the existing switches to be replaced only have 2 wires. I believe I will need to run my own neutral line through the existing conduit. I have done so before and just used a stiff wire with...
Hi guys looking for some advice I'm working in an old property with conduit fed ring mains and lights. I've got a full street of these to test so looking to see the best way to go about it . There is no seperate cpc ran in to any of the switches or lights. The integrity of the conduit is perfect...
Hi guys,
I'm just looking over a job putting power to a summer house but am wondering if anyone has any recommendations on how to lay the cable.
The cable length from the house is 50M going up the house side wall, across a patio, up a 10m wall (onto a balcony garden) then across a balcony...
I’ve been asked to add a couple of extra points to the single ring main in a flat. Building fabric is concrete, all of the electrical installation is steel conduit buried in the concrete.
I opened the consumer unit and could only see one CPC for a radial socket, as well as the main Earth. No...
Hi this is my first post here.
I’m a newly qualified spark mainly working in domestic houses, I got a job coming up where I’m planning to install pvc conduit for some sockets in garage attached to a house.
Would installing pvc conduit affect the fire rating of a consumer unit or would I just...
Looking for writen guide to bending Conduit.
All conduit bending guidance seems to be done through word of mouth.
Looking for a writen guide even if ancient
There must be something writen down with guidelines, angles etc. There seem to be US guides but nothing for the UK.
Thanks.
Evening, is there a place to get good quality 20mm round plastic conduit lids?
I’ve installed a load this weekend from Screwfix and they don’t seal correctly as the plastic is too thin.
I’ve ended up using two lids on each box!
Thanks.
Good evening
I am currently a training to become an electrician. I do hold both initial verification and periodic testing qualifications however this is an issue I have never personally had to deal with and was never mentioned on any of my courses as often seems to be the case.
Basically I am...
I do very little steel conduit work and can't justify buying a full bender set up.
My dad has a hand held plumbers pipe bender.Would I be able to fit a 20mm former and guide to it to use for bends and sets etc.
Hi All,
I need some advice if you don't mind please. Not an electrician and have just moved into a workshop and electrics were relatively ok but now we need to install some new lighting as cheaply as possible but safely.
We had some LED battens from our old workshop and we've hung them in...
hi guys can someone help me out there with the going rate to install Galv conduit 20mm
The main contractor is providing all the materials.
Is there a going rate per meter? Per cut ? Per point?
Thx
Just wondering if anyone makes a red brick colour conduit?
I want the cable/system to be as discreet as possible as it has to go around the side of the house.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.