Hi Guys. I'm not an alarm installer. Existing alarm system installed approx 20 years ago by me at Sisters. It's an old Electricity Board (later Square one) type System. It's not worked for a few years due to Fault displayed on end panel, therefore not used.
PIR's led's work. LED's on outside...
I am doing a 100 to 200amps (underground) service upgrade.
Can I use the existing 11/4” pvc pipe to run the 200amps rated wires?
What is the smallest size of wire I can use for the 200amps?
Is (2) #2/0awg copper & (1) #6awg neutral copper ok?
Current situation: Great room is greatly deprived of light in one-half of the room.
Solution: Add two recessed lights to the current figuration.
I'm not sure how exactly to connect the new lights to the existing lights. I have seen where some explain to connect directly to one light and not...
I'm building a small rental annexe at my own house, which will be supplied by a new local sub-main, with local metering. This includes one existing bedroom which will become part of the annexe.
This room has an existing ring final in 2.5mm, all in good condition. Rather than run two new 2.5s, a...
Hello Forum,
I need to replace the hob in the kitchen as it is faulty.
I would like to be able to use an induction hob, so I need to make sure that the wiring and mcb on the cooker circuit is the right specification.
The combination Oven (1 small / 1 Large ) has a Max load of 4.1Kw.
The...
I’m working in a two gang box, currently has two switches (1 3way with a neutral wire, on old 2 pole switch)
I’m trying to replace the old 2 pole switch with a Dimmer Switch that requires a Neutral Wire.
The 3way switch next to it has a neutral wire.
All other neutrals are cut short and...
Evening all. So got a job coming up; adding new circuit to exsiting DB. When I do my very, do I just need to do it for new circuits added, or do I need to list all circuits on the very even though I’m only adding new one? .
hi all,
My house is a typical 1930s semi. Seems that the partition walls between each room are stud walls. There is only one single socket in each bedroom which is clearly not ideal therefore i want to add more. The upstairs sockets are fed off a 4mm radial so I am thinking of ripping it out...
Hi All. Just a little help I need connecting a electric oven and induction hob. The existing is a 32 amp MCB in the consumer unit. A 4m run of 6mm sq t&e cable from mcb going to a 45A cooker control switch. From here a 6mm sq t&e going into cooker connection unit. I have removed the old electric...
If I was replacing an existing light fitting in a domestic premises, making no alteration or addition to the circuitry, would I then be obligated to provide that circuit with 30mA RCD protection if it didn't already have it?
Hi, everyone
I'm moving some light fittings. The current fittings are wired so there is only a switched live to each fitting. The permanent live is fed to a junction box along with the switch and the switched lives go from there to the fittings.
The existing wiring is a real mess - literally...
Hi all,
I appreciate that this is a question that has been answered a lot but each response I could find was for slightly different set up to mine, so hoping you guys might be able to advise. If any work is needed I will get an electrician out, but don't really want to take time off work and...
There is a double socket on the wall where the main feed comes in and this is then connected to a none switch fused socket. Iv'e been told i can add a other fused switched socket and connect both together then run 2 additional sockets off the fused switch one?
Hi, neighbour has asked if I would run new cable from existing cooker control unit to new oven/grill. The easiest way to run cable without disruption would be under existing kitchen cupboards. Cable would be 2.5mm or 4mm depending on oven. Is it ok to run this,this way ? and would it be better...
Hi, neighbour has asked me if I would move his cooker control switch for him. Since new position of it is further away,this would require joining existing cable via JB or, as is preferable, running a new cable. Running a new cable is a fairly big job,so do the regs allow a JB to be used in this...
hello replaceing both front and back pir lights and got abit stuck with where I need to put the switch live wire as they both currently have a manual switch overide
Current wiring front and back
New front light
New back light
Just abit confuses what to do with switch live wire.
Any help...
Just been asked to quote to wire a new kitchen extension. I realise that the new extension must conform to the 18th IEE regs. The existing wiring in the remainder of the building has the sockets lower that the stated 450mm and the light switches are higher than 1200mm. Do these have to be re...
Hi All
I have tried to wire in a doorbell and I'm having trouble getting the wire through the hole on the inside to the outside and vice versa. I know the hole is at an angle and no matter how much wire I feed through it doesn't seem to come out the other end. I made the error of pulling out...
I'm your average DIYer and after advice about replacing a pendant light with a new flush metal fitting. I can fix the new light to the ceiling and the existing rose sits within the void of the new fitting without any clearance issues. Is it OK to leave it in place and wire the new fitting into...
Hi, I am a first time DIY poster - hoping to navigate the tricky line between getting a bit of a steer in the right direction and not requesting step by step instruction.
I am hoping to DIY the electrics on my extension, and in advance of the project I am trying to map the order of outlets on...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.