instructions
-
P
solar edge rj45 wiring
HI I opened up my se4000 and found no rj45 plug socket, all i found was a set of termination pins with ethernet marked on them. I thought i followed the wiring correct but my solar edge monitoring site has had no data sent, even though the lcd display says s ok. Has anybody had a solaredge...- poheZ
- Thread
- found instructions inverter reading solar wiring
- Replies: 14
- Forum: Solar PV Forum | Solar Panels Forum
-
M
Dimmer rating not making sense
Went to a house the other day as dining room lights not working. 4 x 40/50w gu10's on a dimmer, dimmer faulty. Looking round the house there was an incredible amount of incandescent lighting mostly on dimmers so I suggested to customer that it may be worth spending an extra couple of £'s on the...- mhar
- Thread
- dimmer instructions making minimum sense suitable
- Replies: 5
- Forum: UK Electrical Forum
-
M
Height of shower over bath
Hello everyone Need a bit of advise I have been asked to install a bath in a room that was previously a wet room for a disabled person. Now as per usual the customers don't want to spend a lot of money. At the moment there is an electric shower installed at a height of approximately 750mm to... -
M
Flex and cooker circuits
Do cookers need to be connected with heat resistant flex and if so can you tell me where the reg is. Have been arguing with a collegue about this. Thanks- Monitor
- Thread
- aus cable circuit circuits cooker flex instructions manufacturers
- Replies: 4
- Forum: Australia
-
N
Fluke 1652c instructions
HI guys, I just bought a fluke 1652c and I am looking for some clear instructions on how to use it. Any suggestions where to look on line? Thanks- Neil
- Thread
- fluke instruction instructions
- Replies: 3
- Forum: Electrical Tools and Products
-
M
Manrose 1351 remote fan timer control
I was looking at one of these to upgrade an existing fan. It is installed in conjunction with a double pole fused spur isolator. The timer control takes a permanent live and a switched live. So if the double pole switch is off and the bathroom light is still on then the fan timer unit unit still...- murf20
- Thread
- bathroom control fan instructions light method remote rose switch timer
- Replies: 1
- Forum: Electrical Wiring, Theories and Regulations
-
O
ELECSA Certification Scheme Elecsa Annual Visit
Yes, its that time of year again, got my library, certificates, calibration certificate, insurance, paperwork in order. Got a site where I did recently finished a total rewire available for site visit. Got tea/coffee & bickies ready. Any suggestions for what they are asking this year?- Octopus
- Thread
- annual anyway assessment certification certsure elecsa instructions manufacturers scheme visit
- Replies: 12
- Forum: Certification NICEIC, NAPIT, Stroma, BECSA Forum
-
S
why is new meter tripping rcd
any one tell me why a new meter would trip rcd repeatedly .- sirius
- Thread
- before instructions loose meter new rcd supply tripping
- Replies: 8
- Forum: Industrial Electricians' Talk
-
T
240V Bathroom extractor fan in zone 1?
My electrician says he can't sign off the installation in my new loft conversion because the 240V extractor fan is in zone 1 (directly above the shower), and hence violates the Regs. He says the easiest option is to replace it with a 12V one, and locate the transformer remotely. Disappointed, I...- Toad
- Thread
- 240v aus bathroom electrician extractor extractor fan fan height instructions shower suitable
- Replies: 52
- Forum: Australia
-
P
Could anyone email me fluke 1651 instructions?
Hi all does anyone have these at all?- p11jor
- Thread
- anyone aus email fluke instruction instructions
- Replies: 3
- Forum: Australia
-
N
Idiotic instructions did make me laugh
5ft light fitting opened the box , removed end caps ,removed diffuser , removed center contol gear tray found instructions and it read !! Firstly unpack your light fitting ....... Mmmm instructions are in the fitting how can i do that second remove end caps ...........Mmmmm instructions are in...- nickblake
- Thread
- fitting instruction instructions laugh remove removed
- Replies: 1
- Forum: Electricians Chat - Off Topic Chat
-
O
Extractors & fuses
All I attended the Elecsa update in Woking last night - useful as it was there was one "thing" that stood out was their emphasis on extractor fans being fused down to the "manufacturers instructions". So given that 90%+ of fans suggest fusing down to 3A, and given that most will need live and...- Octopus
- Thread
- aus fuse fused fuses instructions light switch
- Replies: 19
- Forum: Australia
-
DIY Wicks CU - Fitting and installation instructions included
Reading the new Wickes catalogue. I like the two pages on Gas Safe and using a registered installer The electrical section no mention of safety / Part P or anything, altought they do have this little gem on offer. You'll notice the the last line states "Fitting and installation instructions... -
P
Bathroom fan, 3 pole isolation or fused spur?
Just picked up a timed fan and 3 pole switch. Fan is 4" 20 watt. I was going to run 3 core and earth from 3 plate light via 3 pole switch and to fan as per normal. Just read manufacturers instructions and it says must be a double pole fused (3 amp) spur. Can't see the logic to that. What...- Penance
- Thread
- aus bathroom fan fuse fused fused spur instructions isolation light spur switch
- Replies: 13
- Forum: Australia
-
R
Underfloor Heating Issue
I've recently just installed a floorwarmers UFH system. Consists of two cables and two IB-TR8100 thermostats (touch screen types). Installed as instructions detailed. But now when powered up the floor temp just reads error which indicates (from instructions). The is the same with both units. Did...- robbie2399
- Thread
- aus floor heating installed instructions issue thermostats underfloor underfloor heating units
- Replies: 3
- Forum: Australia
-
S
Shower instructions!
Hi All, I have a shower to install for a very difficult customer. When quoted for the job I stated as its only on 6mm cable so she has to get a shower of equal or less kw than the one being replaced. So what does she do? Buys a 9.5kw shower when I pointed out the wording on the quote she...- Shock Doctor
- Thread
- aus instruction instructions shower
- Replies: 3
- Forum: Australia
-
S
RCBO/CU Problem
Went to change mcbs to rcbo's in a wylex board that's used for total control heating. Then I hit a problem as some off the rcbo's don't fit as the neutral bar is in the way! Instead of the main neutral feed to the bar being cable it was one of those copper pre made ones so can't move it up... -
D
Megger 1552 instructions say "Rechargeable batteries must not be used"?
Hi, does anyone know why Megger insist on no rechargeable batteries in their MFT 1552? It explicitly mentions it in the instructions there.. Cheers- DomB
- Thread
- batteries instruction instructions megger
- Replies: 13
- Forum: Electrical Tools and Products
-
T
Square D 2-Channel Time Switch
Hi Hopefully somebody out there can help with a small problem we have with some car park lighting. After looking at the Board, they seem to be controlled by a timer control uint marked 'Square D CPT 2' there are two of these as well as Square D units CLS110 and CCN225. The CPT2 unit is...- twodogsfred
- Thread
- canada instructions other square switch these time time switch units
- Replies: 1
- Forum: Canada
-
P
like for like shower
guys if your replacing a like for like shower if its not rcd protected does this have to be done as well- Peter Woodford
- Thread
- aus center installation instructions protection required shower
- Replies: 30
- Forum: Australia
OFFICIAL SPONSORS
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
YOUR Unread Posts
-
Is it possible to put a 16mm swa on a 40a mcb protected by an rcd
- Latest: brianmoooore
-
-
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.