Good afternoon,
I wonder if someone could please give me some advice on a problem I am having with my bedroom lights. I have replaced the switches for new ones.
The wall light in the bedroom is controlled by a dimmer switch by the door and then by a switch either side of the bed. The dimmer...
Hi all,
I just moved into a new home that has a post light outside on the lawn that didn’t work with the sensor. I know I have power to it because when I wire the light to the house (bypassing the sensor), the lights stays on continuously.
I’ve changed the bulb, sensor and lantern piece...
I have 2 light switches that I want to move about 10 feet. I can’t go up or down with the wiring, so I’m thinking wiremold with 12 ga thhn . They control an inside garage light and an outside dusk to dawn light outside the garage. Can I simply extend the switch legs that way?
Does bathroom light circuit required to have dedicated circuit or is it ok to be wired to other light circuits?
I am getting quotes for electricians and what to make sure they are doing the right thing. From my past experience most of a cheaper trades persons would cut a lot of corners and it...
I have undercabinet lights that are low voltage. They work xenon pucks just fine. I want to convert to low voltage LEDS. Supposedly these are 12V DC but when I hook 12V DC LED pucks up, they don't work.
There is a switch to turn these on that is 120 volts. Somewhere buried behind the wall...
Hi Folks,
I wonder if someone would be good enough to help, please.
I have a new light fitting that has 2 slots, one for live and one for neutral. There are many wires from the ceiling going into the old fitting, so what I need to know is which ones go into the 2 slots in the new fitting.
I...
Hi,
I had a question in my head that turned out to two and then BANG im confused.
I need help with calculation here and explanation to get this right. If i want to build a lamp with 20 light bulbs in a 230V home. Each light bulb is 2watt.
How much current will they take when they are in...
I have a working circuit setup connecting the CU to a switch and light. I want to add an additional light to this circuit, do it use the Brown or Black as live. See images attached of existing termination and loop.
Hi, I have a new light for the bathroom after the other stopped working but these are the wires I'm confronted with. I have tried to wire with the black as live no joy and then the brown as live no joy I'm so confused. when wired up the light fixing is showing live on the tester yet no light...
Good afternoon guys, got a new light fitting, which is not supplied with the usual female terminals for wiring but rather has a short wire permanently attached. I know many people would just connect the cable with a choc block or wago, perhaps wrap it in tape and then just shove it through the...
Hi All, I was changing a light fitting (something I've done many times before). Since it was a switched live to the ceiling fitting I had left the circuit still live (I know but no comments about that please!). Touched the neutral and got a small shock. So used a test screwdriver to see if...
Hi.
I'm not an electrician, I'm just a homeowner who thought they were about to do something as simple as replace a bulb only to find the task seems more confusing.
We have some kitchen units and inside them are some LED lights. I've attached a couple of photos (light and ligh2).
So I went...
I'm trying to install a pendant (single bulb) in a ceiling light fixture. I've run into an issue with the wiring of the fixture box.
Here's the setup of the wires:
5 green wires (never hot, I suspect ground)
5 white wires (never hot, I suspect neutral)
5 brown wires (one is hot but they are...
Just interested in peoples thinking on using the neutral through the earthing system like I came across today. I've come across many wrong polarities tripping mcbs before but not this.
The outside front door light live conductor was wired into the lightswitch inside but the neutral was wired...
This switch controls 2 outdoor lights. The lights each have 2 live, 2 neutral and 2 earth's plugged into them.
This switch didn't work and when I looked behind it was wired like this!
Anybody know how this should be wired??
Thank you!
Hey folks
Apologies if my question is too basic. I am an Electrical Engineer but do not work in the field. I am looking for feedback to ensure safety.
I have a dimmable floor lamp that uses Halogen lights. It takes 300 Watts or 500 Watts Halogen lights that run on 110Volts
The dimmer stopped...
Hi all.
DIY question. I've gone to replace a broken pull chord light in my bathroom (switching off mains power at MCU and testing before touching with a Voltage Tester Pen).
There are 2 exposed red wires from two separate sets of housing, an exposed earth wire and a neutral wire that is...
Hi all you guys out there. i have a Toyota Coaster converted to a motorhome and I love it however I have an issue with brake warning light not extinguishing. From what I understand ,and after looking at the schematic, the lamp is on when either the hand brake is applied or brake fluid level is...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.