wired

  1. H

    retrofit fire alarm to wired smoke detectors in home

    Hi Is this possible. I have wired in smoke detectors in each room in a 4 bed semi. However they are not loud enough and I worry in the event of a fire they will not wake anyone if they sound during the night. I'd like to retrofit a fire alarm to the system which sounds if any smoke detector...
  2. HoverSPRX

    No Overload Protection on DB wired to Busbar

    Hi all, I recently carried out an EICR on a biolabs, it has a DB in the mains room that was wired direct into the busbar on 25mm tails within 3M. The busbar is on a 200A fuse and the DB in question is a 24 way three phase board. I know that 20 + years ago when this was installed some guy has...
  3. C

    Is my house wired wrongly?

    Hello folks, I hope you don't mind but I've just joined up to ask this question. I just took two adjacent mains sockets off the wall in my bedroom to do some wallpapering, and having switched off at the consumer unit, I also tested with a multimeter to make doubly sure they were off. One of...
  4. S

    Ring Final Circuit wired in 4 core SWA

    Hi Gents, Have an existing circuit at a warehouse where a single 4mm 4core SWA has been used as a Ring Final Circuit. Two cores are in connectors in the back of the socket outlets thus creating a ring. The SWA is therefore the sole means of earthing. There are No banjo's at the sockets and the...
  5. V

    Hard wired smoke and heat detectors.

    Hi hope someone can help? My dad needs electrical re-wiring done to his entire house. The house is in bad repair, and no electrical work has been done on his house for over 35 years. He bought battery smoke alarms recently, but is being told by local electrician that it's mandatory to hard...
  6. H

    Intercom wiring help

    Got an intercom to sort, the pictures speak for themselves I think. What happened was a dog chewed through the cables and some Jack the lad tried to fix it. The ones with orange conductors haven't been touched. The one with a yellow conductor to the terminal has been touched - that is how it is...
  7. S

    Rgb lighting.

    Good evening all, I'm looking for some advice on rgb setups. If I wanted several rgb floods to work simultaneously from the same remote would they be wired in the same way as led strips threw an amplifier if so where could I get a rgb wired fitting. Or would there be some sort of signal which...
  8. A

    Fixed wired testing in situ

    I have got some heaters etc to do and after reading my PAT420 manual it can test fixed wire equipment in situ. It will do continuity test @200mA and touch leakage. Would this be OK or do I need to connect it to my tester? I have read a lot but I would like some opinions from people that have...
  9. P

    French wiring book showing Type AC 40a breaker with N and L wired opposite

    Hi all. I've just had my house in France upgraded to single phase. I've bought a consumer unit as i only want a basic set up (minimal electric is used in my house!) and am going to put it in myself. I have a book which teaches you how to wire up. The consumer unit comes pre-packed with one...
  10. C

    Boiler wired from lighting circuit

    Hello. I'm just looking for a bit of advice. I had a new boiler fitted a few months ago. An electrician came and wired it up and left me a Minor Electrical Installation Works certificate. ive just had a plumber round to check the work and he says the electrician has wired the boiler from the...
  11. Soulsurfer

    Old building lighting issues!

    Basically been asked to look into a solution for a customers dwelling / dwellings where they have flats in the same building as they live. At present has old mostly 2 gang switching along ground hallway and up various stairways and between landings and these are junction box wired from two...
  12. S

    Wireing cable reel

    Can anyone tell me how to wire up the picture I have added
  13. J

    installing downlights- wired in conduit

    Looking at a job tomorrow morning- where the customer wants pendants turned into LED down-lights in hall, bathroom and kitchen. He mentioned that there is a loft space above these areas but the existing lights are wired in steel conduit. How do you guys normally go about installing down-lights...
  14. J

    Removing 2 sockets wired together

    Evening....looking for some advice on removing 2 single sockets in a room which is being renovated. It seems one (newish) one has been wired from the other - the cabling disappears under floorboards. I don't want any sockets here anymore so need advice on how to safely remove them, assuming I...
  15. M

    Zs Measurement on plug and play lighting

    Hi Everyone, Any advice on the following - Lighting circuit in a commercial installation (shop), Fixed wiring to Junction Box, The new light fittings are wired using 2.5mm plug and play flex's which are fed from the fixed wired jb's. Where shoul Zs be measured ? At the end of the fixed wiring ie...
  16. D

    New PIR lights off of photocell

    Hi chaps, Went to look at a job tonight in my town - client has an existing photocell sensor doing her outside lights with from what I can see is a three core and earth feeding it. As it's difficult getting back into the home for power, they asked if it was possible to get power from the...
  17. the pict

    Texecom Alarm Dialer

    As I said in another post not my usual thing but... so I am of to fit this later and I think I have it sussed the only part I am unsure of is the 12VDC connections I take it the 12v and 0v are pos and neg from the aux supplly respectivly P
  18. C

    New Hard Wired Smoke Alarm

    Hello, everyone. Four weeks ago, an electrician came to my flat and installed a smoke alarm. He wired it up to the lights on the fuse box. A cable runs from the fuse box, into the alarm on the ceiling right next to it. Here's the thing. Since installing it, the cost of my electricity has...
  19. HappyHippyDad

    Straight wired and crosswired Ethernet connection?

    Evening everyone.. I have just been experimenting with a cat5 wall plate on one end of the cat5 cable and an RJ45 on the other end. The RJ45 connects to my router and the wallplate is situated in the office. I then connect a standard Ethernet cable (RJ45 on both ends) from the wall plate to...
  20. V

    Junction Box for Extending Old Wired Fuse Board

    I went to look at a job the other day for a customer to install a Hot Tub supply in the garden. Whilst there I found that an 'electrician' in the past had extended all the cables down from where an old wired fuse board used to be located to an RCD protected CU. It was basically a bodge where...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock