Hi Folks
First posting. My background is in joinery with any little knowledge on electricity picked up as I went along which isn't enough to answer my query.
The lad lives in a flat in a large block about 150 years old. In the flat is a room about 6 feet x 5 feet containing a wc and wash...
Hi, someone wants an electric hob of rating 6Kw fitted in a static home thats feed by a 40a MCB there is one 32a ring final, two 6a lighting and one 16a oven circuit, after applying diversity the installation is already over its maximum demand a little without adding the hob.
It is unlikely...
Been asked by a customer to quote for a 3 phase 100amp supply to his new build 5/6 bedroom house. His meter by the front gates 135-150m from house. Cable will be buried in ducts, i've done some working out myself (long time since i've had to do this). Using a 70 degree thermosetting cable its...
dmelec
Thread
3 phase
center
customer
house
installing
meter
new
phase
quote
supply
hi there im thinking of getting some sort of chasing machine i already have a dust extractor anyone recommend one. just for odd chases is it worth it . i was thinking of a makita cordless grinder i know i couldnt use the extractor on that but whats the dust like when cutting out boxes and chases...
I am looking to start installing charge points at domestic dwellings. Was just wondering if yous could give me a bit more info on these as regards to regs etc.
Hope somebody can help
I am a time served sparks and a PV installer with all the relevant qualification.
I have installed around 250 PV systems and signed them off as I m NICEIC registered.
The MCS was dealt with through the companies I was installing for.
So here is the question-
As the...
Hi Guys
I am in need of some help. i have just installed a new bathroom extractor. Since the installation, the following happens:
isolator in off position turns the light on and off as usual - extractor fan not working as expected
isolator turned on, causes the bathroom light to turn on and...
Prefix - I've tried to post this in automotive, but it would not let me. This may be because I have not been recently active. Apologies if this is the wrong platform for this post.
Firstly- my apologies if I have posted this in the wrong section - I am nota qualified or trainee electrician. I...
basejumper31
Thread
advice
before
conversion
electric
electrical
electricians vans
electrics
installing
van
vehicle
I'm DIY installing a 1 gang LightwaveRF dimmer.
I currently have a Tenby switch (which I think is 2-way, but only actively 1-way).
As per the installation guide (http://lightwaverf.com/wp-content/uploads/2015/10/JSJSLW200.pdf) I need a
Switched LiveWire Out
Live Wire In
Which wires...
Hi,
I'm currently on a level 2 C&G course at college with a bit of experience.
I have to install a socket outside in the shed in my own house.
I have a few questions i'm not too sure about:
1. is SWA cable the only one to use for taking power to shed or can I use T&E run in conduit? Is...
Hi, haven't been here for a while.:waving:
Just a quick one, what tests and certificates needed, if installing a couple of circuits, 2A loads from the control panel in the plant room, it will be supplying boilers
Don't say its a full wack EIC , and if I am concerned only with circuits I am...
I'm trying to for a PIR with a light but unsure how to connect. I have good knowledge and can install plugs etc have installed lights before. The pir has a NAL connection. What goes into A? And how would I install a light? Based in UK.
adeel718
Thread
attach
install
installed
installing
light
pir
room
sensor
Hi this is my first question. I've searched the forum and be live I'm ok but wanted to double check. Is it ok for me to install this I've to a 13a socket where my existing oven is.
Energy consumption 0.85 kWh
Rated voltage 230-240
Power 2600 2800 w
Current 11-12 amp
Top element 1200w...
I have to provide power for 10 appliances.Each appliance will be provided with own mcb.
The distribution board is 50 meter far away. So I will install a sub board in the room where the appliances will go.the sub board will be fed from the distribution board.If I install the subboard with a...
Hi , thinking of putting in some under cabinet lighting and plinth lighting in the kitchen , want to use leds,m my question is where is the ideal place to locate the drivers/transformers and whats the minimum IP rating for the lights - location is in kitchen? cheers
Hi - I've had a single conventional oven delivered that I want to install. I have to connect it to a junction box connecting to the exposed wires that lead to the fused switch on the wall - what type of junction box should I use - the builders depot type places go up to a maximum of 30AMP - is...
So I'm doing wiring for a hot tub, I've designed a simple circuit
is there anything any one would change or do differently?
Want other people's advice or opinions :) the hot tub is 32amps
I'm putting a lot of LED downlighters in various rooms in my house. What are you meant to do the long metal strip that's attached to the bulb holder?
Doc
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.