I’ve probably broken every rule in the book with this. Was asked if I could do a cable joint between a 6mm T+E and a 2c 6mm SWA. It had to be as unobtrusive as possible as I was on a front wall of a graded building. The T+E ran for 6” below the rendering corbel so the joint would be on the...
Knobhead
Thread
book
broken
earth
every
joint
probably
roman
seconds
times
Could do with a few idea's here, normally do new installs so don't come across this problem much.
I need to add a 16a MCB to a board that has no spare ways. It has 2 lighting, 2 sockets, and central heating circuits(5 way fuseboard). The fuseboard is in a busy office area. What are my...
ricardo123
Thread
aus
before
consumer
consumer unit
help
needed
out
probably
unit
i am going to finish my first pv installation tomorrow, and i have a question about the meter.
so the way i have wired the pv panels from the consumer board is:
16mcb from consumer board
AC isolator
Generating meter
Ac isolator in loft
inverter
dc isolators
pv panels
my question...
just watching politics on tv ( it was left on that channel!) anyway cameron complaining about nhs getting charged over 300 pounds to replace light switch.
in the background a mp shouted that 300 for light switch is about right what do you think?
thekingiam
Thread
aus
light
light switch
probably
replacement
switch
Hi all,
New to the site and to the trade. My main fuse and consumer unit are located on my dining room wall covered by a unit. I know that if I would like to move the consumer unit to the kitchen (which is over 3m away) I will require a switch fuse. Can I, and if so how do I get the the main...
gav809
Thread
aus
consumer
fuse
indent
main
main fuse
probably
switch
testing a hotel chain type you have all stayed in them
anyways DBs for rooms 1or2 are mounted in side service ducts over the years and possibly since build some of the stop cocks and pipe work are above the DBs and Im concerened as due to the age some have leaked in the past my question is...
I recently passed my 17th Edition regs and also have Part P and 2392, but am not on a competent persons scheme yet.
I just wanted to check that I am now technically qualified to fill out BS7671 certificates including Installation certs?
Also, does anyone have any advice on where to get blank...
Hi guys,
Had a situation the other day where the armour sheath on sub mains was carrying a voltage of about 55V.The sheath was not being used as an earth and was only there to give protection to the cable. Can anyone tell me why this occured?
Many thaks
sdc8843
Thread
armour
aus
carrying
earth
probably
sheath
voltage
volts
Hi all, been rewireing lighting in house and fitted new CU but whilst there found the cooker switch and socket are too close to cooker ie level with edge of it.
What I want to know is as the client don't want to move it what do I put on installation cert as it is a non compliance? thanks in...
Hello there..
Have my NICEIC domestic installer assesment in June with Mike Newberry. I am in the East Devon area. Has anyone else on here been assesed by him, just wondering what he is like?
Thank you,
Sy
Demand Five | watch Cowboy Builders, Season 2 - episode 3, Episode 3 link to the show
What a programme this week competent person scheme my arse, i loved the carrier bag cant see what was wrong with that at all give your replies and thoughts guys.
mars6394
Thread
another
aus
builder
builders
carrier
channel
cowboy
probably
Evening
I have been asked to wire up some wall lights. The wires have already been installed and are poking out of the walls. The lady that owns the house doesn't know how they have been installed and what they are connected too! Is there a simple way of finding out what they are connected too? ;)
hi looking for some help i am doing some load test in shops to see if i can fit some new heaters
i am doing a load test at the main board with tong testers and getting my results ok but i dont now if my cable head fuse is 60 amp or 80 amp with out cutting the seal on the main fuse what...
marty1234
Thread
aus
cable
doing
fuse
fuses
load
meter
power
probably
scottish
supply
test
hi guys...
i have been testing lately and have found my megger 1553 has been giving me higher r1+r2 results than the Zs results... i use the same leads, always use good batteries and have it calibrated? is the machine at fault? has anyone ever had similar experiances? im aware that there maybe...
bororich
Thread
check
earth
leads
megger
metal
probably
readings
strange
test
Guys,
just thinking, how sad on a sunday morning. If you had a consumer unit in a garage ran from the main board in the house would you do the Ze tests in the house ( i am thinking yes unless you had a earth spike near the garage is this right). Also if you did put in a earth spike at the...
Hey up all,
Nowt 2 do with th'electrics but thort id spread the word to ne1 who goes to gigs or concerts.
Avoid this bunch of ****** money robbin ******* like the plague.
Misses booked tickets 2 Muse at NIA birmingham 4 next tuesday and after a whole host of emails we finally got a pretty...
After carrying out a PIR on a domestic property do you have to label up the consumer unit with the appropriate stickers, such as the date of next inspection.?
and
if any stickers are not there i.e rcd stickers, is it upto the inspector to place them on the board?
cheers
Went to survey a job earlier. While I was there I wanted to have a look at the C.U, I was told that it was it had been changed in November by an electrician who had been recommended to then, he also installed some lights, some sockets in the kitchen and a 10kw shower.
When I had a look at...
ian
Thread
aus
because
electrical work
job
probably
really
shower
worst
years
put in first shaver socket after all these years and custumer is saying that it has a low level hum when some thing is pluged in ,now i would say this is normal due to the isolating transforma with in. going to look at end of week but am i right in my feelings
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.