Hi,
Recently been to a property that requires a board change but got no main switch. Usually the service fuse has no tag (lol) so i simply remove fuse crack on an re insert.
today i came across one were it had a big steel covering. On the PIR it had been picked up as "unable to access supply...
Hi,
I am going to buy a set of these, below, you can get a set of three, 20mm, 25mm and 32mm I think it was.
I had a go with them in Eddies the other day as the Armeg bloke was there, I have to say I was very impressed with them.
Acceler8% Sheet Steel Holesaws
What do you use and do you...
Hi,
Following my threads about using structural steel for the earth...
Well, today was in the area and stopped by the office where the EV charger is going and they are building this building right next door to it, its exactly the same, I stopped and as it happens I managed to speak with the...
Recently went to a job that another lad on our firm had started to give him a hand.
A 3 phase supply has been installed to a steel container ( 16 mm2 4 core SWA , and separate 16mm2 earth ). The container is to temporarily house medical gas/ vacuum pumps that supply various wards on our local...
How's this for a means of earthing this steel conduit is acting as a tt arrangement, although brilliant ze readings, 6.41 ohms 34a. What do you all think to this.
Aye ups all,
Called to a mates job today to help out, the premises are gonna be a mechanics garage, which is a steel structure embedded in concrete, now I noticed that he's taken the supply for the new premises from the garage next door which is also owned by the customer, I'm assuming he's...
Just checking that I am required to install a 300ma RCD supplying the structure as per 740.410.3 (it cost £8k to put up so is not exactly temporary).. Used to store vehicles.
Well I just got myself an apprenticeship :grin: and was wondering what brand would be best for steel cap boots, also do electricians tend to wear a certain colour like black or honey coloured (sounds stupid I know lol)
What brand of tools would be good to start off with, mainly the basics like...
In a house where steel supports have been put in . Cables will have to be run beside these girders. The cables are resting on the metal but these don't need to be earthed ?
Do they ?
Hi,
Got a job where I need to run cables round outside of building under 50mm of lime render, need to put it in capping.
Where can I get 3mm steel capping? Any ideas as im struggling to find it.
quick question does steel conduit need bonding at the start and finish of the run, because i have a job coming off soon replacing some metal twin fan extract units to plastic inline fans, at the moment the conduit it attached to the fan and the fan is earthed via a separate cpc in the conduit...
Hello,
I have a pond filter, that has a short (3-4m) run of flex to a junction box, and I want to protect it, but can't decide on the best conduit. The flex will be discreet but not buried, and will run with the hoses from the filter across a flowerbed. (It's at risk of boots & hand trowels...
can I wire a house in flexible conduit and singles ?, as done in other parts of Europe, there does not seem to be any specific info in BS7671 or part P,
Let me explain further
I have 20 years experience uk trained ,i have done commercial and domestic but I have also pent a few years working in...
vmgbarra
Thread
conduit
double
flexible
house
insulated
steel
wire
Hi guys
Been asked to perform some remedial works on site....lot of which is Missing 100mm galvanised trunking lids missing.
Can they be bought alone ? ( as i cant find them ) or will the whole trunking section needs to be replaced ?
does anybody have any better ideas ?
ta
daiplayer
Thread
along
brand
different
seperate
steelsteel trunking
trunking
wholesalers
Hi all,
I have a commercial premises (school) that requires installation of main bonding at a block which is an outbuilding from the main school.
Now the bonding in the main school is 50mm, however the cable feeding this outbuilding is just a 25mm 4core.
So what size should I be using...
londonlec
Thread
bonding
building
copper
main
outbuilding
steel
supply
system
Hi guys, just quoting for a job in a warehouse (steel frame). They want a 2G socket in the middle of the warehouse floor between vehicles. No option of chasing out the concrete floor. So are there any products available to hang from the perlins or RSJ's somehow?
Any ideas?
Thanks, Ad.
Hi has anyone used Schletter's ClampFit-H product for fixing modules directly to the roof sheet - see below:
ClampFit-H product for landscape mounting on a trapezoidal roof sheet. This
is a rail-less fastening system, which incorporates a module
clamp integrated into the fastener. No rails...
Miss Sunshine
Thread
box
fixing
modules
new
product
profile
sheets
steel
hi,im about to embark on installing some power in a steel shipping container,im going to use a Schneider 6 way board rcd main switch.there are 2 air con units going in here but onlt one will be running at any one time,the other is purely as a back up if one fails, both rated at 5kw cooling and...
On a TN system , i want to bond the structural steel on a farm shed. But the submain across to the farm shed is only 10mm Twin and Earth, so only a 4mm cpc is supplied? I was going to install a 10mm cpc to the steel from the local shed db? any help please.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.