amps

Recent contents Top users
  1. M

    25VDC @ 14,000 Amps?

    Getting involved with electrolyser systems. Korean manufacture. They cannot seem to clearly tell me if the 25VDC @ 14,000 Amps they use in the system will or will not injure or kill? Any thoughts welcome. Regards, Mal
  2. S

    Socket extension question - max amps

    This has no doubt been asked often by non electrical minded folk like me but when a socket extension says maximum 13amps, does actually that mean 4 plugs fitted with 3amp fuses like desk lamps etc (or 5a+5a+3a) or does it go by the actual amps of the equipment and you could have say 6 plugs with...
    • stoutlad
    • Thread
    • amps equipment extension fuses max question socket total watts
    • Replies: 21
    • Forum: UK Electrical Forum
  3. S

    Will a 10mm PYRO take 80 amps ?

    Hi, I need to change the main incoming fuse from 60A to 80A but there is a 10mm pyro feeding the property and i dont really want to replace this. The reason I need to up the supply to 80A as I am installing a sunbed which runs at 40A single phase. The load will never constantly be running at...
    • sycamore89
    • Thread
    • 10mm amps aus pyro
    • Replies: 31
    • Forum: Australia
  4. S

    no amps on a new system

    hi i have just done a 4kw system it is with sanyo panels and a power 1 inverter 2 strings of 8 and its on a south faceing roof but it is only doing 9 units a day i have 330 volts on each string but very little amps i have had a look at every connection and all looks good i have looked at reverse...
  5. Y

    Lost Amps

    Basically the circuit is of of an air heater battery consisting of : 3 x 2Kw heaters wired in star to a 3Ph & N supply , plus a capacitor start 1 Ph motor on L1 phase . Total amps of heater = 8.5 amps / phase , motor draws 6.5 amps on L1 phase when run separately . But when both are run together...
    • Yorks Sparky
    • Thread
    • amps canada
    • Replies: 14
    • Forum: Canada
  6. A

    Car 12v amps -- help!

    Hi there, Sorry, I'm not a sparky and hoping that someone can help me with a question! I have a wireless cctv camera and reciever, they are both 12v, one is 200mA the other 500mA, if I wire this directly to a car battery (I assume a high ampage) will it 'blow them up'.... or is it that what...
    • assuan
    • Thread
    • 12v amps aus car help help!
    • Replies: 22
    • Forum: Australia
  7. T

    Amps and milliamps

    I was just pondering.....if a consumer unit has say a 32mA mcb protected circuit, upon which I use an appliance with a 15 Amp fuse in it's plug........ wouldn't the mcb always blow before the 15 amp fuse in the plug ????? 15 AMPS seems to be so much tougher than 32 mAmps. Or don't I understand...
    • Tom Evans
    • Thread
    • amps aus
    • Replies: 14
    • Forum: Australia
  8. G

    how many amps?

    I know this is a really daft question, so please dont shout at me but I cant work it out. I have 5 x 50 watt 12 volt bulbs powered by a 230 volt to 12 volt transformer. Could someone kindly tell me how many amps they use??? :confused: Thanks
    • gpz900jim
    • Thread
    • amps aus
    • Replies: 32
    • Forum: Australia
  9. R

    Sealey EH3300 drawing 30 Amps!

    Customer has bought a Sealey EH3300 heater. He tried putting it on a plugtop and it didn't work, so he has asked me to connect it. It is, as the name suggests, a 3.3kW heater. No problem, thought I, it can be installed on a fused spur to an existing radial circuit containing just three...
    • ringer
    • Thread
    • amps canada drawing
    • Replies: 11
    • Forum: Canada
  10. P

    What size ground cable do I need for 40 amps?

    I will have to replace a ground cable from my circuit breaker box to my buildings earth line. The devices it is grounding have a max load of 8750kw / 220v = 39,7 Amp. It's going to run along a 6 SQ MM cable but I don't know what size the ground cable should be for this. I read 1.5 SQ MM is...
  11. jibjob

    Bonding TV ariels & amps

    Hi all, I've been asked by a TV ariel installation company to quote for bonding a soon to be installed TV ariel and amplifier. The service will be shared by a number of flats in the same buliding. Can't find anything in the BRB regarding the regs on this. Can anyone help/enlighten?:)
  12. W

    amps volts and whats?

    Hi everyone, having read a few forums recently this looks like the one offering the best advice.Clearly a lot of us are here because we have a problem we cant figure out and need some help and i am no exception. Some months ago i fitted a system to my camper in the uk and then took a 28 day...
  13. D

    Fuse 40 with appliance 13 amps

    Hi there, in the fuse box I hava fuse for 40 amps and an "heavy" wire going to the cooker. However my cooker is 13 amps! Normally I would have changed the 40 amps fuse from the box but the plug of the cooker is fused, with a 13 amps fuse. So I guess that is enough to prevent the cooker from...
    • dylan86
    • Thread
    • already amps appliance aus cooker fuse socket
    • Replies: 5
    • Forum: Australia
  14. C

    back to basics higher the volts lower the amps?

    hi guys am i right in saying that generally the higher the amps the lower the volts ?? watts divided by amps = volts watts divided by volts = amps amps x volts = watts taking that in mind a 12v extra low voltage spot light which is 50 watts = 4.1 amps 240v low voltage 100w bulb = 0.4...
  15. N

    Watts to Amps

    For single phase its easy Amps = Watts/Volts. Is it as easy for 3 phase? Amps = Watts/Volts/3 per phase. or is there a root 2 in their somewhere? I need to know to calc the voltage drop along the supply. Thanks in advance for any offers.
  16. F

    Not enough amps maybe????and Rcd tripping

    Morning sparkies:) Was on a job when his neighbour asked if i could have a quick look at his place, as his power trips of all the time? And his bills have gone up dramatically. Has a home energy meter that tells him he's using power even with every thing off??? 5 bed 15 years old no paperwork...
    • Firebucket
    • Thread
    • amps aus enough kitchen lights power rcd rcd tripping sorry tripping
    • Replies: 3
    • Forum: Australia
  17. D

    3 phase motor, high resistance & high amps.

    at work the other day, a 3 phase motor was running very high amps, when everything checked out we found a loose connection on 1 of the phases back at the DB, cable was melted and burnt. now for me i always thought high resistance would mean less amps would flow, the other electrician put the...
    • Dave0098
    • Thread
    • 3 phase amps cable canada current motor phase resistance
    • Replies: 3
    • Forum: Canada
  18. W

    amps carried in cables

    can someone please help me to understand how many amps 1mm + 1.5mm + 2.5mm + 4mm + 6mm + 10mm twin & earth cables can carry please or put me in the right direction, Also what size breakers are appropriate for the 1mm + 1.5mm + 2.5mm + 4mm + 6mm + 10mm twin & earth cables
    • wannabesparky
    • Thread
    • amps aus cables carried
    • Replies: 4
    • Forum: Australia

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
UK Tiling Forums
Tiling Tools
Tiling Forum UK
Electrical Advice
UK Tiling Forum
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock