Hi all. Looking for advice here. The mother in law had her house extended and totally rewired by someone that said to her he was a qualified sparks. I've been up the loft and found crimped wires and not even clipped down and a whole host of lovely terminal block connections. One set of these has...
Therolster
Thread
block
don't
light
measuring
outside
outside light
terminal
volt
volts
Allreet, Does anyone have the above or let me know how it needs wired? Its the usual social housing rubbish thats normally issued.
Terminals on programmer at are the usual - N - L - 1 - 2 - 3 - 4
Terminals on the stat are the usualy L&N - L1, LX, L2
cHEERS
i have a 2 core and earth cable going to my single switch it has l1 l2 and c on the back i can wire the 2 core into the l1 and c but there is no where for the earth as it is in a plastic pattress box instead of a metal back box so no where for the earth to be clamped however i noticed the...
Kev1
Thread
earth
light
light switch
metal
need help
question
single
switch
terminal
Hi all, new here and after some advice on a twin dimmer switch purchased from a large warehouse type diy store.
It is marked as a two gang two way dimmer, so I was expecting to find six terminals; one common and two switched live on each of the two sides.
Yet there is only one common.
Now...
Itisonlyme
Thread
2 way
common
downstairs
light
lights
switch
terminal
upstairs
wonder can anyone help, i have a danfoss 2 channel timeclock which was switching itself on, i had a grasslin towerchron QE2 2 channel time clock in boot of car and swapped it over but it just runs heating and hot water even before anything comes up on display screen.... i thought would be...
Unable to access any(but can see most) of the round type screw terminal joint boxes.
Hello,
I carried out anEICR last week, and the entire house is filled with SELV recessed downlighting.
All of the (78fittings) have been skimmed around/over at some point, and the(dangeling) round type...
found this under floorboards, i understand how it works but don know if its ok/standard practice or a giant bodge to skimp on 2 jb's! (ive tried google but anything you search for with light wiring always seems to brings up 2 way switching!)
bottom left is circuit out to next lighting jb...
After installing some LED fittings in a bathroom and disabling an electric shower circuit I carried out a check on the whole installation. All fine until I used my Di-LOG probe to probe the switch plate screws to check that I had not pinched any live wires in the light switch back boxes around...
Sting Ray
Thread
between
earth
light
light switch
switch
switched
terminal
voltage
volts
I know its the wrong forum but does anyone know about intruder alarms, i'm replacing my old knackered panel with a new version but different terminations.
Guys I'm gutted I've lost my britool insulated terminal driver 3.5mm.
I can't seem to find a replacement online any where. It was brill as it was a dead long one 150mm shaft.
Anyone know where I can buy a new one I can't see them anywhere online ****ing devastated had that since started my...
Got a metal light switch to fit but surpisingly there's no earth terminal on the switch plate.
It's Jo Jo branded and has BS3676 marked on it so presumably meets regs?
The metal back box is earthed so the screws would presumably earth the front plate when fitted, but this doesn't seem ideal...
Recently came across a 6 terminal 20Amp junction box with 12 T&E cables coming out of it and an additional chocy block inside! Is that a record? It was being used as the only distribution box for the upstairs lighting of a 3 bed semi.
I wanted to fit a 13th but the earth terminal wasn't having...
Hi all again
I'm doing another condition report for a property, no cpc for sockets, cooker lighting, what's the best way to test continuity, I'm thinking of doing the same way as R1+ R2 line to earth terminal, also would you record results in r2 box or R1+ R2 box, I'm having a bad day
Hi, I'm a council tenant and just had some work done in my kitchen, which included a new electrical installation. There was previously a single sockets ring main, and a new kitchen sockets ring main was added, which in itself seems fine. But I'm concerned about the pre-existing ring main. This...
Camdonian
Thread
block
electric
electrical
regs
regulations
tape
terminalterminal block
Greetings,
I've purchased an ECD RCBO which I've used before to some success. However, although it physically fits in place of the circuit breaker the bottom of it doesn't reach the line bus bar. Can anyone point me at the correct replacement RCBO for this type of breaker. Images of the...
Hello,
I have been looking for MCB (originally Legrand 061 64) which is laying horizontally with respect to DB and is connected by the means of external copper PIN on DB (i.e. Screw terminal on 1 side of the MCB only).
I had a look into different suppliers RS, CEF, ScrewFix and unfortunately I...
Hi,
Just been to a job this morning, customer wants power to the garage, no problems there, just one question and I wondered what people tend to do in this situation.
On the back of the house wall is a switched fused spur on a 20A MCB from the consumer unit at the front of the house, its...
I am currently renovating the missus house and have noticed a couple of things i need advice about, i am a qualified builder and plumber and have quite a bit of knowledge of domestic property electrics but i do 'NOT' carry out any electrical work myself as i do like to adhere to regulations...
makken
Thread
advice
attach
bonding
consumer
domestic
earth
needed
please
terminal
water
Amateur question here (and I may have picked the incorrect subforum too)
I want to attach a single common ground to 12 separate buttons, with individual wires rather than daisy-chaining them. I'm wondering what the best tool for this would be. In my mind I have pictured a terminal block, but...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.