Hello just wondering if anyone could help me! I have to test a circuit tomorrow wired in SWA that is using its armoring as its earth, To carry out the R1+R2 test how would i eliminate any parallel paths? Surely the only real way to do this would be to remove the cable from the side of the metal...
Hi all,
My fluke tester has just started giving funny readings on continuity I.e 72 ohms for open circuit. I've checked it on my check box and they are all out apart from zero....
Just wondered if anyone else has had this problem??
Looks like ill be sending it off tomorrow lol
Thank in advance
Rich
I've been reading here & elsewhere about issuing a MWC for accessory replacements, and the merits of. Me personally I agree with issuing a MWC for a like for like replacement of a socket outlet for example.However, my MWC requires results for essential tests:
1) R1+R2 or R2. 2) Insulation...
Hi, am doing a continuity test on living room light, downstairs MCB off, last light in circuit, incoming to light disconnected, disconnect switch twin and earth, cross connected Earth and neutral in switch, did a continuity test at light and the RCD trips.
Any help appreciated, only thing I...
coatesykid
Thread
cable
connected
continuity
earth
rcd
rcd tripping
still
switch
test
tripping
Hi, I'm new to the forums so am not sure if this is the right section for these questions, but it appears to be a good area to place them.
I'm pretty new to learning about electrical installation, and as i go along, i realise there's still some gaps in my understanding which I can't seem to...
Had to leave a job early tonight, so couldn't resolve what should be a simple issue, but now it's buzzing round my brain. I have 5 ceiling rose's and pendants in a good old loop system. All 1 Way. I have good continuity readings at rose numbers 1,2,3 and 5. I have good continuity...
KingKenny
Thread
ceiling
connection
continuity
cpc
issue
reading
rose
switch
Hi Again
Can anyone tell me how i can do an earth test on a kettle with no element in side and nothing to clip test lead to please?
I cant leave it out, can i?
thanks
Hi
i'm going to test some lightning protection tomorrow following on from some extra tape we installed. Im competant with testing the electrodes with the fall of potential method etc.
what im unsure about is the continuity testing, there are 15 down conductors, and i read on here that, using a...
I'm rather new to testing and interpreting results. Did a test two weeks ago on a new ring installed then with continuity results L-L 0.37, N-N 0.36, E-E 0.60 and L- E 0.25. All good. Tested it today and got results L-L 0.17, N-N 0.17, E-E 0.39, L-E 0.05. Not good. I'm testing it again tomorrow...
Was helping a fiend to change some socket outlets, standard white to brushed steel in her kitchen. She only had the house re wired 2 years ago - got the part P paperwork.
This is what we found behind one socket. WTF was the bloke thinking??
Also obviously doesn't bother with grommets.
I also...
Hello chaps and chapettes,
Continuity of final ring circuit I measured:
L-L = 1.45
E-E = 0.8
but measuring N-N I got 108.8....???!!!!!!
Any ideas..? Or are those readings good in my limited experience and consequently I'm an idiot.
A out of date Cadbury's cream egg for the most sarcastic...
se7aq
Thread
circuit
continuity
don't
final
readings
ring
ring circuit
those
Hi
I have my Elecsa assessment in under two weeks and ive never felt so stressed in my life! I've changed my C.U. to use as my job as i thought it would be easier but im really struggling with the testing especially on the downstairs ring final sockets. Ive done end to ends and got Line 0.61ohms...
Hi all,
i've been asked to test a number of fixed appliances in a flat and haven't has any experience with these yet. I'm wondering do I just disconnect them from the wall and using my fluke 1651 multi meter do insulation and continuity tests at the flex going into the appliance or would you...
Hi Guys,
Has anyone come across this SMPS from RS, 445-107.
Blurb says its class 1, because it has an earth pin.
I cannot get a circuit from the earth pin to the '-' of the output.
I have sent RS a question about this but have not had a reply.
Must fail it as a class 1 appliance.
hubsy
Thread
because
class
continuity
earth
output
power
supply
switch
Practicing for my 2395 C&G on a friends house
tester KT63 6 month old
he has 3 ring finals for sockets in his house, reason he asked me if I would test his house is that his RCD keep tripping out overnight ( once a week )
1st Ring final Circuit is fine
Circuit 2 has given me some results I...
Joe Hyde
Thread
circuit
continuity
earth
fault
fault finding
finding
please
ring
sockets
I brought an ethos continuity tester from City electrical factors yesterday and I paid £50 for it as they guy said he woould do me a deal on it as he rekons they were £113 odd trade or something which just doesnt sound right. im thinking of taking it back and going for a fluke but just wondered...
Dear All
I expect this is going to raise a few eyebrows but..
I know that is your unsure about an earth bond to a water main you can do a continuity test and look for a figure under 0.05 ohms.
I have also read that you can do an IR test, under 23K ohms needs bonding and over 23K does not
Now...
Hello people.
I'm a gold card holding spark with a commercial background (metal munchin'). Recently I've got a job 2nd fixing flats, no problems except i didn't have a test rig so i bought a Fluke 1652 one 2nd hand, had it calibrated and changed the batteries.
The problem is with the...
jon one
Thread
apart
clips
continuity
fluke
leads
readings
someone
test
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.